manualshive.com logo in svg

Aerohive access point, Руководство по развертыванию

Бесплатное руководство по развертыванию для точки доступа Aerohive доступно для загрузки с manualshive.com. Получите это руководство сегодня и узнайте, как настроить вашу сеть для оптимального подключения. Скачайте руководство сейчас!

Поделиться
Скачать
background image

Deployment Guide

53

 H

IVE

AP 340 P

RODUCT

 O

VERVIEW

Smart PoE

The HiveAP 300 series applies the Aerohive concept of smart PoE to adjust power consumption as necessitated by 
varying levels of available power. No adjustments are needed when the power level is 20 W (watts) or higher. If the 
available power drops to a range between 18 and 20 W, the HiveAP disables the ETH1 interface. If the level drops to 
the 15 – 18 W range, it then switches from 3x3 MIMO (Multiple In, Multiple Out) to 2x3 (see 

"MIMO" on page 57

). In 

rare cases when the power drops between 13.6 and 15 W and further power conservation is necessary, the HiveAP 
reduces the speed on ETH0 from 10/100/1000 Mbps to 10/100 Mbps. Finally, in the event that there is a problem 
with the PoE switch or Ethernet cable and the power falls between 0 and 13.6 W, the HiveAP disables its wireless 
interfaces and returns its ETH0 and ETH1 interfaces to 10/100/1000 Mbps speeds. Through the application of smart 
PoE, the HiveAP 340 can make power usage adjustments so that it can continue functioning even when the available 
power level drops.

Aggregate and Redundant Interfaces

By default ETH0 and ETH1 act as two individual Ethernet interfaces. When both interfaces are connected to the 
network and are in backhaul mode, the HiveAP transmits broadcast traffic only through ETH0. The HiveAP transmits 
broadcast traffic through ETH1 only when ETH0 does not have network connectivity. When both Ethernet interfaces 
are connected to the network and are in access mode, then the HiveAP transmits broadcast traffic through all the 
access interfaces: ETH0, ETH1, and all wireless subinterfaces in access mode.

In addition to using ETH0 and ETH1 as individual interfaces, you can combine them into an aggregate interface 
(agg0) to increase throughput, or combine them into a redundant interface (red0) to increase reliability. The logical 
red0 and agg0 interfaces support all the settings that you can configure for Ethernet interfaces except those 
pertaining to physical link characteristics such as link speed. See the sections below for configuration information.

Aggregate Interface

You can increase throughput onto the wired network by combining ETH0 and ETH1 into a single logically aggregated 
interface called "agg0". The aggregate interface effectively doubles the bandwidth that each physical interface has 
when used individually. In this configuration, both Ethernet ports actively forward traffic, the HiveAP applying an 
internal scheduling mechanism based on the source MAC address of each packet to send traffic through the 
aggregate member interfaces. To configure an aggregate interface, enter the following commands:

interface eth0 bind agg0

interface eth1 bind agg0

In addition to configuring the HiveAP, you must also configure the connecting switch to support EtherChannel. For 
example, the following commands bind two physical Ethernet ports—0/1 and 0/2—to the logical interface 
port-channel group 1 on a Cisco Catalyst 2900 switch running Cisco IOS 12.2:

Switch#conf t

Switch(config)#interface port-channel 1

Switch(config-if)#switchport mode access

Switch(config-if)#spanning-tree portfast

Switch(config-if)#exit

Switch(config)#interface fastEthernet 0/1

Switch(config-if)#switchport mode access

Switch(config-if)#channel-group 1 mode on

Switch(config-if)#spanning-tree portfast

Switch(config-if)#exit

Содержание access point






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для access point

D-Link Rangebooster N 650 Access Point DAP-1353 User Manual preview
Rangebooster N 650 Access Point DAP-1353
Бренд: D-Link Страницы: 67
D-Link DWL-1000AP Quick Install Manual preview
DWL-1000AP
Бренд: D-Link Страницы: 8
D-Link COVR-2202 Simple Setup Manual preview
COVR-2202
Бренд: D-Link Страницы: 2
D-Link DAP-1155 Quick Install Manual preview
DAP-1155
Бренд: D-Link Страницы: 3
D-Link Air Premier DAP-2695 Command Line Interface Reference Manual preview
Air Premier DAP-2695
Бренд: D-Link Страницы: 39
D-Link AirPlus DI-714P+ Brochure preview
AirPlus DI-714P+
Бренд: D-Link Страницы: 5
D-Link AC5300 Quick Install Manual preview
AC5300
Бренд: D-Link Страницы: 12
D-Link SharePort DIR-825 Configuring preview
SharePort DIR-825
Бренд: D-Link Страницы: 20
D-Link Express EtherNetwork DI-604 Owner'S Manual preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 49
IgniteNet SunSpot N300 Quick Start Manual preview
SunSpot N300
Бренд: IgniteNet Страницы: 7
M Box D446559XA Operating Manual preview
D446559XA
Бренд: M Box Страницы: 60
Kogan KAWRTBB300A User Manual preview
KAWRTBB300A
Бренд: Kogan Страницы: 16
Linksys MAX-STREAM MR6350 Regulatory Information preview
MAX-STREAM MR6350
Бренд: Linksys Страницы: 28
Sitecom AC750 User Manual preview
AC750
Бренд: Sitecom Страницы: 54
DX DX-BT19-S User Manual preview
DX-BT19-S
Бренд: DX Страницы: 17
Cradlepoint CradlePoint PHS300tw Quick Start Manual preview
CradlePoint PHS300tw
Бренд: Cradlepoint Страницы: 2
HPE Aruba AP-505H Product End-Of-Life Disassembly Instructions preview
Aruba AP-505H
Бренд: HPE Страницы: 4
Hughes HX260 Installation Manual preview
HX260
Бренд: Hughes Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды