Ace ACE-3105 Скачать руководство пользователя

Страница: 24 / 418

Table of Contents

Installation and Operation Manual

ACE-3105, ACE-3205 Ver. 5.2

ATM Buffer Allocations .....................................................................................

1-20

IMA Functionality ..............................................................................................

1-20

ATM OAM Functionality ....................................................................................

1-20

Continuity Check (CC) .......................................................................................

1-21

Abis Optimization .................................................................................................

1-21

MPLS Utilization ....................................................................................................

1-22

Label Distribution Protocol (LDP) ......................................................................

1-22

Penultimate Hop Popping (PHP) ........................................................................

1-22

Fault Propagation and PSN Connectivity Checks .....................................................

1-24

PPPoE ...................................................................................................................

1-24

Bridge ...................................................................................................................

1-25

MAC Table Handling in Bridge Mode ..................................................................

1-26

Frames Handling in Bridge Mode .......................................................................

1-26

Physical Loopback Tests ........................................................................................

1-27

SNMP and Alarm Traps ..........................................................................................

1-28

SNMP Traps ......................................................................................................

1-28

Alarm Traps ......................................................................................................

1-28

Management ........................................................................................................

1-28

Cross-Network Management ............................................................................

1-28

Management Security .......................................................................................

1-29

1.4

Technical Specifications ............................................................................................

1-30

Chapter 2. Installation and Setup

2.1

Site Requirements and Prerequisites ..........................................................................

2-1

2.2

Package Contents ......................................................................................................

2-2

2.3

Required Equipment ...................................................................................................

2-2

Power Cable............................................................................................................

2-2

Interface Cables ......................................................................................................

2-3

2.4

Connecting to PDH Equipment ....................................................................................

2-3

2.5

Connecting to DSL Network Equipment ......................................................................

2-4

Using DSL Interfaces ...............................................................................................

2-4

2.6

Connecting to Packet-Switched Networks ...................................................................

2-5

Using Fiber Optic Ethernet Interface ........................................................................

2-5

Using Electrical Ethernet Interface ...........................................................................

2-6

2.7

Connecting to a Control Terminal ...............................................................................

2-7

2.8

Connecting to Power ..................................................................................................

2-8

Connecting to AC Power ..........................................................................................

2-8

Connecting to DC Power .........................................................................................

2-8

Chapter 3. Operation

3.1

Turning On the Unit ...................................................................................................

3-1

3.2

LED Indicators ............................................................................................................

3-2

3.3

Default Settings .........................................................................................................

3-3

Configuration Defaults ............................................................................................

3-3

3.4

Configuration Alternatives ..........................................................................................

3-4

Working with an ASCII-based Control Terminal .........................................................

3-4

Logging In via the Terminal/Telnet Interface ........................................................

3-6

ASCII Screen Format ...........................................................................................

3-7

Principles of Navigation ......................................................................................

3-8

Hot Keys ............................................................................................................

3-8

Working with ConfiguRAD .......................................................................................

3-9

Содержание ACE-3105



































































































































































































































































































































































































































Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды

Ace ACE-3105, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды