manualshive.com logo in svg

Ace ACE-3105, Инструкция по установке и эксплуатации

Поделиться
Скачать
Ace ACE-3105 Скачать руководство пользователя страница 327

Installation and Operation Manual 

Chapter 

 

6  Monitoring and Diagnostics 

ACE-3105, ACE-3205 Ver. 5.2 

Recovering ACE Units 

6-89 

³

 

If no response is received: 

1.

 

Check that the remote device is properly connected and configured (IP 
addresses and routing). 

2.

 

Check the path connectivity using the trace route command. 

³

 

To use trace route to check the path connectivity: 

1.

 

Go to Diagnostics>Applications>IP>Trace Route.  

2.

 

Start the race route. 

 1. Destination IP address                  ... (0.0.0.0) 

 2. Start 

PPPoE 

In the case of PPPoE, you must have an operational PPPoE session active. 

³

 

To determine logical layer faults on PPPoE: 

1.

 

Make sure to have an operational PPPoE session active. 

2.

 

Go to Monitoring>Logical layer>PPPoE. 

    Session status                     >   (Down) 

    Session id                         ... (0) 

    Remote MAC                         ... (00-00-00-00-00-00)  

    Local MAC                          ... (00-00-00-00-00-00) 

    Actual back-off[sec]               ... (0)  

    PPP LCP status                     >   (Down) 

    PPP IPCP status                    >   (Down) 

    PPP authentication                 >   (None) 

    Local IP                           ... (0.0.0.0)  

    Remote MRU                         ... (0) 

3.

 

Check the status of the PPPoE session and what negotiation parts opposite 
the BRAS/LNS were completed successfully. 

4.

 

In case the local IP is not received, check the credential allocation for the 
session on the RADIUS server. 

³

 

To check the credential allocation: 

1.

 

Go to Configuration>Logical layer>PPPoE. 

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды