Ace ACE-3105 Скачать руководство пользователя | Manualshive

Страница: 342 / 418

background image

Chapter

6 Monitoring and Diagnostics

Installation and Operation Manual

6-104

Recovering ACE Units

ACE-3105, ACE-3205 Ver. 5.2

2.

Observe the frequency of the Jitter buffer underruns.

In cases where they periodically recur, continue investigating the clocking
settings and the topology.

The frequency of the Underruns can be easily analyzed using the log file.
In cases where a specific pattern cannot be identified, continue as
follows:

3.

Go to Monitoring>System>Event log>View event log.

2008-07-16 10:01:25 | Underrun End PW 3

2008-07-16 10:01:25 | PW Up 3 - 3

2008-07-16 10:01:24 | Rx R=1 Start PW 3

| 2008-07-16 10:01:24 | Underrun Start PW 3

v 2008-07-16 10:01:24 | PW Down 3 - 3

2008-07-16 10:00:23 | Rx R=1 End PW 3

2008-07-16 09:50:33 | Underrun End PW 3

2008-07-16 09:50:33 | PW Up 3 - 3

2008-07-16 09:50:32 | Rx L|M=100 End PW 3

2008-07-16 09:50:04 | Rx R=1 Start PW 3

Rx R=1 means that the remote unit was experiencing Underrun condition.

Rx L|M=100 means that the remote unit is reporting on failure on the
TDM interface.

When Rx L|M is up together with Underrun event, continue with the fault
on the remote TDM interface procedure.

In case the missing packets counter is also increasing along with the
underruns, it is possible that the underruns are simply caused by the
massive packet loss events and not by high PDV.

In this case, continue using the packet loss troubleshooting procedure.

4.

Check that the ETH/GbE uplink is running at Full-Duplex mode:

5.

Go to Monitoring>Physical layer>Port>Ethernet>Status.

MAC address

... (00-20-D2-2A-60-55)

Mode

> (Full Duplex)

6.

Increase the jitter buffer configured depth.

The configured jitter buffer cannot be changed on the fly, which means it
would require deleting the relevant PW.

7.

Go to Configuration>Applications>Multiservice over PSN>PW>Service
parameters.

8.

Check the current jitter buffer settings.

2. Jitter buffer (usec)[1000 - 32000] ... (3000)

9.

Go to Configuration>Applications>Multiservice over PSN>PW.

«
...
340
341
342
343
344
...
»

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACE-3105

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 66

Бренд: Advantech Страницы: 66

Бренд: Alphatech Страницы: 16

Бренд: ESD Страницы: 104

Бренд: Avid Technology Страницы: 152

Бренд: ActionTec Страницы: 6

Бренд: Telstra Страницы: 100

Бренд: Teltonika Страницы: 6

Bluetooth Gateway

Бренд: Xlink Страницы: 3

Бренд: Viola Systems Страницы: 53

Бренд: eyeLock Страницы: 32

TP-Link TD-W9970

Бренд: iiNet Страницы: 12

Бренд: OpenVox Страницы: 60

Бренд: OpenVox Страницы: 69

Sure Cross P2-KR

Бренд: Banner Страницы: 8

Бренд: halo connect Страницы: 16

Scopia TIP Gateway

Бренд: RADVision Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды