manualshive.com logo in svg

Ace ACE-3105, Инструкция по установке и эксплуатации

"Ace ACE-3105" - профессиональный инструмент с высокой производительностью. Для установки и эксплуатации необходимо ознакомиться с Руководством по установке и эксплуатации. Скачайте его бесплатно с manualshive.com. Необходимый инструмент для успешного выполнения задач.

Поделиться
Скачать
background image

Chapter 

 

6  Monitoring and Diagnostics 

Installation and Operation Manual 

6-90 

Recovering ACE Units 

ACE-3105, ACE-3205 Ver. 5.2 

 1. ID[1 - 4]                              ... (-) 

 2. AC name                                ... (-) 

 3. Service name                           ... (-) 

 4. Scheduled restart                      >   (-) 

 5. Back-off random range[sec][0 - 600]    ... (-) 

 6. Minimum authentication level           >   (-) 

 7. Username                               ... (-) 

 8. Password                               ... (-) 

 9. Confirm password                       ... (-) 

10. VLAN tagging                           >   (-) 

2.

 

Reenter the user name and the password for the session in order to restart 
the PPPoE session. 

3.

 

Check the minimum authentication level (CHAP/PAP) to match the security 
settings on the LNS. 

LDP 

This applies if LDP is used to exchange PW and tunnel labels. 

³

 

To monitor the LDP: 

•

 

Go to Monitoring>Applications>MPLS>LDP>Hello.  

LDP ID         Peer LDP ID         Type    Interval   Time left 

VCCV-BFD 

The VCCV-BFD is a keep-alive mechanism that monitors the path between the PW 
devices and is used to extend failure messages between units. 

In case the BFD fails to receive the keep-alive message in the given time-frame, a 
proper notification is sent and the PW is disabled (Down). 

³

 

To analyze the status of the BFD mechanism:  

•

 

Go to Monitoring>Applications> Multiservice over PSN>PW>Status. 

    PW Number[1 - 66]                   ... (2) 

    PW type                             >   (ATM VP N to 1)  

    VCCV_BFD status                     >   (Up)  

There are four basic states for the BFD mechanism: 

•

 

Init: The BFD failed to receive any BFD messages from the remote unit. Check 
if on the remote unit BFD is enabled. 

•

 

Control-detection-time-expired: The local system did not get BFD packets 
from each other at the predefined time interval. Check the network path 
between the ACE unit and the remote unit.  

Increase the detection multiplier and the Min Tx interval to see if the alarm 
can be cleared. 

ƒ

 

To access the Detection Multiplier and Min TX parameters, go to 
Configuration>Applications>Multiservice over PSN>PW>General 
parameters. 

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACE-3105

Viessmann WAGO 750-8212/000-100 Installation And Service Instructions For Contractors preview
WAGO 750-8212/000-100
Бренд: Viessmann Страницы: 36
auto maskin NMEA2000/J1939 Quick Installation Manual preview
NMEA2000/J1939
Бренд: auto maskin Страницы: 13
Elvaco CMe2100 G3 Quick Manual preview
CMe2100 G3
Бренд: Elvaco Страницы: 2
Dispel Wicket User Manual preview
Wicket
Бренд: Dispel Страницы: 17
Advantech EDG-4508+ User Manual preview
EDG-4508+
Бренд: Advantech Страницы: 82
NETGEAR CG4500BD User Manual preview
CG4500BD
Бренд: NETGEAR Страницы: 53
Microhard Systems IPn3Gii Operating Manual preview
IPn3Gii
Бренд: Microhard Systems Страницы: 186
Sangoma Netborder SS7 Quick Start Manual preview
Netborder SS7
Бренд: Sangoma Страницы: 4
Ericsson EDACS Jessica Operator'S Manual preview
EDACS Jessica
Бренд: Ericsson Страницы: 12
Gree VRF Service Manual preview
VRF
Бренд: Gree Страницы: 31
VOPtel VG2020 User Manual preview
VG2020
Бренд: VOPtel Страницы: 38
evertz 78908MG-10GE2 User Manual preview
78908MG-10GE2
Бренд: evertz Страницы: 52
Watchguard Firebox X1000 Hardware Manual preview
Firebox X1000
Бренд: Watchguard Страницы: 18
enphase CT-100-SPLIT ROW Installation Instruction preview
CT-100-SPLIT ROW
Бренд: enphase Страницы: 2
ZyXEL Communications 4381 Installation Instructions preview
4381
Бренд: ZyXEL Communications Страницы: 2
ZyXEL Communications 3415 Installation Instructions preview
3415
Бренд: ZyXEL Communications Страницы: 2
Cooper Bussmann 915U-2 User Manual preview
915U-2
Бренд: Cooper Bussmann Страницы: 115
PiiGAB 810 Getting Started preview
810
Бренд: PiiGAB Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды