manualshive.com logo in svg

Ace ACE-3105, Инструкция по установке и эксплуатации

"Ace ACE-3105" - профессиональный инструмент с высокой производительностью. Для установки и эксплуатации необходимо ознакомиться с Руководством по установке и эксплуатации. Скачайте его бесплатно с manualshive.com. Необходимый инструмент для успешного выполнения задач.

Поделиться
Скачать
background image

Chapter 

 

6  Monitoring and Diagnostics 

Installation and Operation Manual 

6-92 

Recovering ACE Units 

ACE-3105, ACE-3205 Ver. 5.2 

    ETH Port 1   PW type ATM VP N to 1  

    RX packets                          ... (0)              

    RX congestion dropped               ... (0)           

    TX packets                          ... (473)             

    TX congestion dropped               ... (0)             

    TX timeout                          ... (0)             

    Packet loss event                   ... (0)         

    Mis-order dropped packets           ... (0)          

    Reordered packets                   ... (0)          

    Unknown VP/VC cells                 ... (0)          

³

 

If packets have not been received, proceed as follows: 

1.

 

Check PW In/Out labels on both end PW devices. 

2.

 

Go to Configuration>Applications>Multiservice over PSN>PW>General 
parameters and change the In/Out labels used on the end points to another 
value to rule out duplication issues. 

5. Out PW label[16 - 1048575]           ... (17) 

6. In PW label[16 - 65534]              ... (17) 

3.

 

Check if the LDP mode is used. An LDP PW ID means that it is activate. 

4.

 

To check on the LDP mode, go to Configuration>Applications>Multiservice 
over PSN>PW>General parameters. 

4. Provisioning mode                    >   (LDP PW id) 

5.

 

In LDP/MPLS mode, change the Tunnel label/Label range. 

6.

 

Check whether the LDP PW ID is the same on both end PW devices and 
whether it is unique to the PW identified below: 

7.

 

To view the PW parameters, go to Configuration>Applications>Multiservice 
over PSN>PW>General parameters. 

4. Provisioning mode                    >   (LDP PW id) 

5. PW ID[1 - 4294967295]                ... (5) 

8.

 

If the situation remains unchanged, check the path connectivity connecting 
the PW end points, either by enabling BFD or validating the path using the 
PSN OAM tools. 

Device Disconnected 

The device is no longer reachable remotely (telnet/SNMP/Web) 

 

In case of remote management loss to the ACE unit, you should use a local serial 
connection to analyze the problem. 

 

Management failure can be related to: 

•

 

Management path disconnected 

•

 

Incorrect access parameters 

•

 

Failure of the Management plane in the ACE unit. 

Note 

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACE-3105

Yacht Devices NMEA 0183 User Manual preview
NMEA 0183
Бренд: Yacht Devices Страницы: 36
TIS KNX-PORT Installation Manual preview
KNX-PORT
Бренд: TIS Страницы: 5
Grandstream Networks GXW 410 Series Applications preview
GXW 410 Series
Бренд: Grandstream Networks Страницы: 4
Nomadix NWCG User Manual preview
NWCG
Бренд: Nomadix Страницы: 204
RAKwireless RAK7243 Pilot Gateway Pro User Manual preview
RAK7243 Pilot Gateway Pro
Бренд: RAKwireless Страницы: 18
ENANCER ONLY SMART HOME D-FTC2E User Manual preview
ONLY SMART HOME D-FTC2E
Бренд: ENANCER Страницы: 9
Oki BMG7011 User Manual preview
BMG7011
Бренд: Oki Страницы: 70
Yeastar Technology Yeastar TA400 Installation Manual preview
Yeastar TA400
Бренд: Yeastar Technology Страницы: 10
ADTRAN 834-v6 Quick Start Manual preview
834-v6
Бренд: ADTRAN Страницы: 8
YZ Systems YZ Connect User Manual preview
YZ Connect
Бренд: YZ Systems Страницы: 25
Valcom IP Solutions PagePro VIP-204 User Manual preview
IP Solutions PagePro VIP-204
Бренд: Valcom Страницы: 4
Ubee DDW366 Safety And Installation Manual preview
DDW366
Бренд: Ubee Страницы: 7
Dormakaba BEST Wi-Q Installation Instructions Manual preview
BEST Wi-Q
Бренд: Dormakaba Страницы: 8
Fanvil G100S User Manual preview
G100S
Бренд: Fanvil Страницы: 41
Fanvil GA10 User Manual preview
GA10
Бренд: Fanvil Страницы: 54
Planet WPG-210N Quick Installation Manual preview
WPG-210N
Бренд: Planet Страницы: 2
Planet WPG-130N User Manual preview
WPG-130N
Бренд: Planet Страницы: 53
ZyXEL Communications VMG3625-T50B Quick Start Manual preview
VMG3625-T50B
Бренд: ZyXEL Communications Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды