Ace ACE-3105 страница 70 Скачать руководство пользователя | Manualshive

Страница: 70 / 418

background image

Chapter

2 Installation and Setup

Installation and Operation Manual

2-8 Connecting

to

Power

ACE-3105, ACE-3205 Ver. 5.2

2.8

Connecting to Power

ACE-3105, ACE-3205 has either AC or DC power supply (as ordered), provided via
one or two integrated power supply units. A standard power cable is supplied
with the unit.

Connecting to AC Power

AC power is supplied to ACE-3105, ACE-3205 via a 3-prong plug. AC power should
be supplied through the 1.5m (5 ft) standard power cable terminated by a 3-
prong plug. The cable is provided with the unit.

In ACE-3105, ACE-3205, two power cables may be connected to the unit
simultaneously.

Before connecting to power or disconnecting any other cable, the protective
ground terminals of this unit must be connected to the protective ground
conductor of the mains power cord. If you are using an extension cord (power
cable), make sure it is grounded as well.
A grounding cable must be connected to the dedicated grounding screw, located
in next to the power supply outlet(s).

Any interruption of the protective (grounding) conductor (inside or outside the
instrument) or disconnecting of the protective earth terminal can make this unit
dangerous. Intentional interruption is prohibited.

The line fuse is located in an integral-type fuse holder located on the rear/front
panel of the unit. Make sure that only fuses of the required rating, as marked on
the rear/front panel, are used for replacement. Do not use repaired fuses or
short-circuit the fuse holder. Always disconnect the mains cable before removing
or replacing the fuse. Whenever it is likely that the fuse protection has been
damaged, make the unit inoperative and secure it against unintended operation.

³

To connect ACE-3105, ACE-3205 to AC power:

1.

Connect the power cable to the AC power connector on the front panel.

2.

Connect the power cable to the mains outlet.

The unit automatically turns.

Connecting to DC Power

³

To connect ACE-3105, ACE-3205 to DC power:

•

Refer to the DC power supply connection supplement, located on the
Technical Documentation CD or at the back of the official printed version of
this manual. Also, refer to the safety instructions at the beginning of this
manual.

Warning

«
...
68
69
70
71
72
...
»

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACE-3105

Бренд: Eaton Страницы: 2

Бренд: TempAlert Страницы: 22

NMEA CONNECT PLUS

Бренд: Calypso Instruments Страницы: 26

Бренд: HALNy Страницы: 8

Бренд: HMS Networks Страницы: 20

Бренд: ZyXEL Communications Страницы: 12

Бренд: Yeastar Technology Страницы: 10

Бренд: H3C Страницы: 39

Бренд: Pathport Страницы: 3

Бренд: Z-Wave Страницы: 68

Thingsee ENVIRONMENT RUGGED

Бренд: Haltian Страницы: 13

Бренд: Gree Страницы: 31

Бренд: Motorola Страницы: 2

Бренд: SSS Siedle Страницы: 2

Бренд: UNION Market Страницы: 36

Бренд: Blonder tongue Страницы: 8

Бренд: Xtream Страницы: 9

OfficeConnect 3CRWE52196

Бренд: 3Com Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды