3M ESPE Elipar DeepCure-L, Руководство по эксплуатации

Страница: 14 / 180

12
SEITE 12 - 148 x 210 mm - 3100021788/01 - SCHWARZ - 20-052 (kn)
dry with a soft, lint-free cloth. If you do not rinse well
with water, the components will be damaged.
Additional notes: Ensure that the charge contact pins
stay dry and are not touched by any metallic or greasy
parts. Do not bend the charge contact pins while they
dry. Wet charge contact pins cause an operating error
(malfunction message: the LED showing the operating
status of the charger flashes red).
3 CaviWipes™ were used for validation of the cleaning
and disinfection procedure.
Clean Handpiece and Glare Shield
Clean all components with a soft cloth and, if necessary,
a mild cleaning agent (e.g., dish-washing detergent).
Solvents or abrasive cleaners can damage the
components.
Cleaning agents must not enter the device.
왘
To disinfect all components, spray the disinfectant
on a towel and use it to disinfect the device. Do not
spray the disinfectant directly on the handpiece.
- Disinfection agents must not enter the device!
왘
Dry residual disinfectants with a soft and fluff-free
cloth as they damage the plastic components.
왘
Make sure that disinfectants do not come into contact
with the charging socket on the handpiece because
this could impair proper charging.
If necessary, ask the manufacturer of the disinfectant if
its constant use will damage plastic surfaces.
Clean the protection glass with a soft and fluff-free
cloth. Beware of scratches!
Storage of the Handpiece during Extended Periods
of Non-Use
왘
If the handpiece will not be used for a number of
weeks - e.g., during vacation - charge the battery
beforehand or connect the handpiece to the charger
for this time. A safety switch within the battery
prevents a total discharge.
Discharged or nearly discharged batteries must be
recharged as soon as possible.
Return of Old Electric and Electronic
Equipment for Disposal
1. Collection
Users of electric and electronic equipment are required
to collect their old equipment separately from other
waste in accordance with the regulations of the specific
country. Old electric and electronic equipment must not
be disposed of with unsorted household waste. This
separate collection is a prerequisite for recycling and
reprocessing as an important method for preserving
environmental resources.
2. Return and Collection Systems
When your Elipar DeepCure-L is no longer usable,
do not dispose of the device with household waste.
3M Deutschland GmbH has set up special disposal
facilities to handle the equipment. Details about the
procedure for the specific country can be obtained
from the pertinent 3M subsidiary.
3. Removing the Battery for Disposal
To dispose of the battery, disconnect the Elipar LED
curing light from the charger, remove the two screws on
each side of the charging socket and push the lower
half of the housing towards the back, away from the
upper half of the housing. Use a suitable tool to cut the
connecting wires between the battery and the circuit
board and remove the battery for disposal in accordance
with 1. and 2.
Customer Information
No person is authorized to provide any information that
deviates from the information provided in this instruction
sheet.
Warranty
3M Deutschland GmbH warrants this product will be free
from defects in material and manufacture. 3M Deutsch-
land GmbH MAKES NO OTHER WARRANTIES INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. User is
responsible for determining the suitability of the product
for user’s application. If this product is defective within
the warranty period, your exclusive remedy and
3M Deutschland GmbH’s sole obligation shall be repair
or replacement of the 3M Deutschland GmbH product.
Limitation of Liability
Except where prohibited by law, 3M Deutschland GmbH
will not be liable for any loss or damage arising from
this product, whether direct, indirect, special, incidental
or consequential, regardless of the theory asserted,
including warranty, contract, negligence, or strict liability.