YOKOGAWA DL7480 User Manual Download Page 98

Page: 98 / 176

2-43

IM 701450-51E

CAN Bus Signal Analysis Function

2.9 Communication Commands

Command

Function

Page

:TRIGger:CAN:IDENtifier?

Queries all settings related to the Identifier in the trigger* conditions.

2-55

:TRIGger:CAN:IDENtifier:CONDition

Sets the Identifier condition in the trigger* conditions or queries the current 2-55

setting.

:TRIGger:CAN:IDENtifier:ID<x>?

Queries all settings related to the Identifier ID<x> in the trigger* conditions. 2-56

:TRIGger:CAN:IDENtifier:ID<x>:HEXa

Sets the pattern of the Identifier ID in the trigger* conditions in hexadecimal. 2-56

:TRIGger:CAN:IDENtifier:ID<x>:MODE

Enables or disables the Identifier ID<x> in the trigger* conditions or queries 2-56

the current setting.

:TRIGger:CAN:IDENtifier:ID<x>:PATTern

Sets the Identifier ID<x> pattern in the trigger* conditions in binary or

2-56

queries the current setting.

:TRIGger:CAN:IDENtifier:MODE

Sets whether trigger activates on the Identifier in the trigger* conditions or

2-56

queries the current setting.

:TRIGger:CAN:MFORmat

Sets the message format in the trigger* conditions or queries the current

2-56

setting.

:TRIGger:CAN:PATTern?

Queries all settings related the pattern setting of the combination trigger.*

2-56

:TRIGger:CAN:PATTern:CHANnel<x>

Sets the condition (pattern or slope) of each channel of the combination

2-57

trigger* or queries the current setting.

:TRIGger:CAN:PATTern:CLOCk

Sets the clock channel of the combination trigger* or queries the current

2-57

setting.

:TRIGger:CAN:PATTern:CONDition

Sets the pattern condition of the combination trigger* or queries the current 2-57

setting.

:TRIGger:CAN:PFORmat

Sets the pattern format in the trigger* conditions or queries the current

2-57

setting.

:TRIGger:CAN:RTR

Sets whether the trigger activates on a data frame (0) or remote frame (1)

2-57

in the trigger* conditions or queries the current setting.

:TRIGger:CAN:SPOint

Sets the sample point in the trigger* conditions or queries the current

2-57

setting.

:TRIGger:CAN:VDIFf

Sets Vdiff in the trigger* conditions or queries the current setting.

2-57

:TRIGger:TYPE

Sets the trigger type or queries the current setting.

2-57

In the explanation of the function of each command in this section,

analysis

refers to CAN Bus signal analysis.

Trigger

refers to

the trigger of the CAN Bus signal analysis function.

Cursor

refers to the cursor of the CAN Bus signal analysis function.

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands