YOKOGAWA DL7480 User Manual Download Page 110

Page: 110 / 176

2-55

IM 701450-51E

CAN Bus Signal Analysis Function

:TRIGger:CAN:DATA?

Function

Queries all settings related to the Data Field in

the trigger conditions.

Syntax

:TRIGger:CAN:DATA?

Example

:TRIGGER:CAN:DATA? -> :TRIGGER:CAN:

DATA:MODE 1;DLC 8;

PATTERN1 “XXXXXXXX”;

PATTERN2 “XXXX0000”;

PATTERN3 “XXXXXXXX”;

PATTERN4 “XXXXXXXX”;

PATTERN5 “XXXXXXXX”;

PATTERN6 “XXXXXXXX”;

PATTERN7 “XXXXXXXX”;

PATTERN8 “11111111”;CONDITION TRUE

:TRIGger:CAN:DATA:CONDition

Function

Sets the Data Field condition (True/False/

Greater/Less) in the trigger conditions or

queries the current setting.

Syntax

:TRIGger:CAN:DATA:CONDition

{TRUE|FALSe|GREater|LESS}

:TRIGger:CAN:DATA:CONDition?

Example

:TRIGGER:CAN:DATA:CONDITION FALSE

:TRIGGER:CAN:DATA:CONDITION? ->

:TRIGGER:CAN:DATA:CONDITION FALSE

:TRIGger:CAN:DATA:DLC

Function

Sets the number of valid bytes (DLC) of the

Data Field in the trigger conditions or queries

the current setting.

Syntax

:TRIGger:CAN:DATA:DLC {<NRf>}

:TRIGger:CAN:DATA:DLC?

<NRf>=1 to 8

Example

:TRIGGER:CAN:DATA:DLC 6

:TRIGGER:CAN:DATA:DLC? ->

:TRIGGER:CAN:DATA:DLC 6

:TRIGger:CAN:DATA:HEXa<x>

Function

Sets each byte of the Data Field patterns in the

trigger conditions in hexadecimal.

Syntax

:TRIGger:CAN:DATA:HEXa<x>

{<String>}

<x>=1 to 8

Example

:TRIGGER:CAN:DATA:HEXA1 “A3”

:TRIGger:CAN:DATA:MODE

Function

Sets whether trigger activates on the Data Field

in the trigger conditions or queries the current

setting.

Syntax

:TRIGger:CAN:DATA:MODE {<Boolean>}

:TRIGger:CAN:DATA:MODE?

Example

:TRIGGER:CAN:DATA:MODE 1

:TRIGGER:CAN:DATA:MODE? ->

:TRIGGER:CAN:DATA:MODE 1

:TRIGger:CAN:DATA:PATTern<x>

Function

Sets the Data Field pattern in the trigger

conditions in binary or queries the current

setting.

Syntax

:TRIGger:CAN:DATA:PATTern<x>

{<String>}

:TRIGger:CAN:DATA:PATTern<x>?

<x>=1 to 8

Example

:TRIGGER:CAN:DATA:

PATTERN1 “10X10X10”

:TRIGGER:CAN:DATA:PATTERN1? ->

:TRIGGER:CAN:DATA:

PATTERN1 “10X10X10”

:TRIGger:CAN:EFRame

Function

Sets whether trigger activates on the Error

Frame in the trigger conditions or queries the

current setting.

Syntax

:TRIGger:CAN:EFRame {<Boolean>}

:TRIGger:CAN:EFRame?

Example

:TRIGGER:CAN:EFRAME 1

:TRIGGER:CAN:EFRAME? ->

:TRIGGER:CAN:EFRAME 1

:TRIGger:CAN:IDENtifier?

Function

Queries all settings related to the Identifier in

the trigger conditions.

Syntax

:TRIGger:CAN:IDENtifier?

Example

:TRIGGER:CAN:IDENTIFIER? ->

:TRIGGER:CAN:IDENTIFIER:MODE 1;

CONDITION FALSE;ID1:MODE 1;

PATTERN “11111101100”;:TRIGGER:CAN:

IDENTIFIER:ID2:MODE 0;

PATTERN “XXXXXXXXXXX”;:TRIGGER:CAN:

IDENTIFIER:ID3:MODE 0;

PATTERN “XXXXXXXXXXX”;:TRIGGER:CAN:

IDENTIFIER:ID4:MODE 0;

PATTERN “XXXXXXXXXXX”

:TRIGger:CAN:IDENtifier:CONDition

Function

Sets the Identifier condition (True/False) in the

trigger conditions or queries the current setting.

Syntax

:TRIGger:CAN:IDENtifier:CONDition

{TRUE|FALSe}

:TRIGger:CAN:IDENtifier:CONDition?

Example

:TRIGGER:CAN:IDENTIFIER:

CONDITION FALSE

:TRIGGER:CAN:IDENTIFIER:CONDITION?

-> :TRIGGER:CAN:IDENTIFIER:

CONDITION FALSE

2.9 Communication Commands

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands