YOKOGAWA DL7480 User Manual Download Page 44

Page: 44 / 176

1-39

IM 701450-51E

C Bus Signal Analysis Function

Command

Function

Page

:SEARch:I2C:SEARch:NEXT?

Performs the analysis* result search on the data after the current byte and 1-44

returns the search position.

:SEARch:I2C:SEARch:PREVious?

Performs the analysis* result search on the data before the current byte

1-44

and returns the search position.

:SEARch:I2C:SEARch:TYPE

Sets the analysis result search type or queries the current setting.

1-44

:SEARch:TYPE

Sets the search type or queries the current setting.

1-44

C File Group

:FILE:SAVE:I2C:ABORt

Aborts the saving of the data of the detailed analysis list of the analysis.*

1-45

:FILE:SAVE:I2C[:EXECute]

Executes the saving of the data of the detailed analysis list of the analysis* 1-45

(overlap command).

C Trigger Group

:TRIGger:I2C?

Queries all settings related to the trigger.*

1-47

:TRIGger:I2C:ADDRess?

Queries all settings related to the Adrs&Data trigger.*

1-47

:TRIGger:I2C:ADDRess:ABCount

Sets the byte data location for comparing the Data2 Pattern when using A

1-47

drs&Data trigger* or queries the current setting.

:TRIGger:I2C:ADDRess:ADDRess?

Queries all settings related to the address pattern setting for the Adrs&Data 1-47

trigger.*

:TRIGger:I2C:ADDRess:ADDRess:HEXa

Sets the address pattern for the Adrs&Data trigger* in hexadecimal.

1-47

:TRIGger:I2C:ADDRess:ADDRess:MODE

Enables or disables the address pattern for the Adrs&Data trigger* or

1-48

queries the current setting.

:TRIGger:I2C:ADDRess:ADDRess:PATTern

Sets the address pattern for the Adrs&Data trigger* in binary or queries the 1-48

current setting.

:TRIGger:I2C:ADDRess:DATA<x>?

Queries all settings related to each address pattern setting for the

1-48

Adrs&Data trigger.*

:TRIGger:I2C:ADDRess:DATA<x>:CONDition

Sets the condition of each data pattern for the Adrs&Data trigger* or

1-48

queries the current setting.

:TRIGger:I2C:ADDRess:DATA<x>:DBYTe

Sets the number of bytes of the data pattern (Data2 Pattern) for the

1-48

Adrs&Data trigger* or queries the current setting.

:TRIGger:I2C:ADDRess:DATA<x>:HEXa<y>

Sets each data pattern for the Adrs&Data trigger* in hexadecimal.

1-48

:TRIGger:I2C:ADDRess:DATA<x>:MODE

Enables or disables each data pattern for the Adrs&Data trigger* or

1-48

queries the current setting.

:TRIGger:I2C:ADDRess:DATA<x>:PATTern<y>

Sets each data pattern for the Adrs&Data trigger* in binary or queries the

1-48

current setting.

:TRIGger:I2C:BCOunt

Sets the byte count for the Adrs&Data trigger* or queries the current setting.1-49

:TRIGger:I2C:COMBination

Sets the combination trigger* or queries the current setting.

1-49

:TRIGger:I2C:IREStart

Sets whether to ignore the restart condition (YES/NO) of the trigger* or

1-49

queries the current setting.

:TRIGger:I2C:IUNexpected

Sets whether to ignore the start/stop conditions that do not conform to the

1-49

protocol (YES/NO) of the trigger* or queries the current setting.

:TRIGger:I2C:PATTern?

Queries all settings related to each channel pattern setting of the

1-49

combination trigger.*

:TRIGger:I2C:PATTern:CHANnel<x>

Sets the condition (pattern or slope) of each channel of the combination

1-49

trigger* or queries the current setting.

:TRIGger:I2C:PATTern:CLOCk

Sets the clock channel of the combination trigger* or queries the current

1-49

setting.

:TRIGger:I2C:PATTern:CONDition

Sets the pattern condition of the combination trigger* or queries the current 1-49

setting.

:TRIGger:I2C:TYPE

Sets the trigger* type or queries the current setting.

1-49

:TRIGger:TYPE

Sets the trigger type or queries the current setting.

1-50

In the explanation of the function of each command in this section,

analysis refers to I

C Bus signal analysis.

Trigger refers to

the trigger of the I

C Bus signal analysis function.

1.8 Communication Commands

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands