background image

1-30

IM 701450-51E

Executing the Search

32.

Press the Next or Previous soft key.  The search is executed.

When the data matches the determination pattern, the corresponding data (data that

was found) is highlighted in the analysis data list at the bottom of the screen.  The

zoom box moves to the position so that the data that was found is at the center, and

the zoomed waveform of the data that was found is displayed in the zoom waveform

display area.

Pressing the Next soft key searches the data after the highlighted data (to the right) in

the analysis data list at the bottom of the screen.

Pressing the Previous soft key searches the data before the highlighted data (to the

left) in the analysis data list at the bottom of the screen.

If you selected Indefinite State (indefinite data) in step 26 and execute the search,

indefinite data is highlighted.

Search is performed 
to the left

Search is performed 
to the right

1.5 Analyzing/Searching Data

Summary of Contents for DL7480

















































































































































































Reviews: