Yamaha XV19CTMX(C) Service Manual Download Page 81 | Manualshive

Page: 81 / 494

background image

CABLE ROUTING (for XV19S(C)/ XV19M(C)/ XV19CTS(C)/

XV19CTM(C))

2-54

1. Main switch lead
2. Right handlebar switch lead
3. Wire harness
4. Left handlebar switch lead
5. Air temperature sensor lead
6. Front left turn signal/position light lead
7. Headlight lead
8. Front right turn signal/position light lead
9. Headlight coupler (high beam)
10. Headlight coupler (low beam)
11. Air temperature sensor
12. Main switch
A. View with headlight lens unit removed.
B. Place the joint coupler behind the leads.
C. Place the sections of the handlebar switch leads

that are not covered by their protective sleeves in
the rear of the headlight housing.

D. Fasten the headlight leads, front turn

signal/position light leads, and accessory light lead
with the holders along the side of the headlight
housing.

E. Place the headlight leads, front turn signal/position

light leads, and accessory light lead near the base
of the holder.

F. 30 mm (1.18 in)
G. View from rear of headlight lens unit
H. Less than 20 mm (0.79 in). Fasten the headlight

lead (low beam) with the holder, making sure to
fasten the protective sleeve of the lead, not the lead
itself.

I.

Route the headlight lead (high beam) between the

headlight coupler (low beam) and the stay.

J. Route the headlight lead (high beam) behind the

headlight lead (low beam).

K. Secure the plastic band by inserting the projection

on the band into the hole in the headlight housing.

L. Face the end of the plastic band downward.

«
...
79
80
81
82
83
...
»

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

Brand: Kappa Pages: 4

Brand: Öhlins Pages: 2

Mechatronics 35007-01

Brand: Öhlins Pages: 4

McPherson Strut MIR 5H02

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 4

SIDE FORCE 445cc

Brand: Mash Pages: 27

Brand: N-Com Pages: 6

Brand: Jialing Honda Pages: 10

Brand: Crivit Pages: 30

Brand: Bisshops BV Pages: 16

Brand: Corbin Pages: 4

Rally Pack Value Series

Brand: Dowco Pages: 3

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands