Yamaha XV19CTMX(C) Service Manual Download Page 136

Page: 136 / 494

CHASSIS

3-23

EAS21280

CHECKING THE FRONT BRAKE HOSES

The following procedure applies to all of the
brake hoses and brake hose clamps.
1. Check:

• Brake hoses “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose clamps

Loose

→

Tighten the clamp bolt.

3. Hold the vehicle upright and apply the brake

several times.

4. Check:

• Brake hoses

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “FRONT BRAKE” on page 4-35.

EAS21290

CHECKING THE REAR BRAKE HOSES

1. Remove:

• Rider seat

Refer to “GENERAL CHASSIS” on page 4-1.

2. Check:

• Brake hoses “1”

Cracks/damage/wear

→

Replace.

3. Check:

• Brake hose clamp

Loose connection

→

Tighten the clamp bolt.

4. Check:

• Brake hose guide

Loose

→

Tighten the guide bolt.

5. Hold the vehicle upright and apply the brake

several times.

6. Check:

• Brake hoses

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “REAR BRAKE” on page 4-47.

EAS21330

ADJUSTING THE REAR BRAKE LIGHT
SWITCH

NOTE:

The rear brake light switch is operated by move-
ment of the brake pedal. The rear brake light
switch is properly adjusted when the brake light
comes on just before the braking effect starts.

1. Check:

• Rear brake light operation timing

Incorrect

→

Adjust.

2. Adjust:

• Rear brake light operation timing

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Hold the main body “1” of the rear brake light

switch so that it does not rotate and turn the
adjusting nut “2” in direction “a” or “b” until the
rear brake light comes on at the proper time.

Direction “a”

Brake light comes on sooner.

Direction “b”

Brake light comes on later.

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands