Yamaha XV19CTMX(C) Service Manual Download Page 210 | Manualshive

Page: 210 / 494

background image

REAR BRAKE

4-57

EAS22720

CHECKING THE REAR BRAKE MASTER
CYLINDER

1. Check:

• Brake master cylinder

Damage/scratches/wear

→

Replace.

• Brake fluid delivery passages

(brake master cylinder body)
Obstruction

→

Blow out with compressed air.

2. Check:

• Brake master cylinder kit

Damage/scratches/wear

→

Replace.

3. Check:

• Brake fluid reservoir

Cracks/damage

→

Replace.

• Brake fluid reservoir diaphragm

Cracks/damage

→

Replace.

4. Check:

• Brake hoses

Cracks/damage/wear

→

Replace.

EAS22730

ASSEMBLING THE REAR BRAKE MASTER
CYLINDER

WARNING

EWA13520

• Before installation, all internal brake com-

ponents should be cleaned and lubricated
with clean or new brake fluid.

• Never use solvents on internal brake com-

ponents.

EAS22740

INSTALLING THE REAR BRAKE MASTER
CYLINDER

1. Install:

• Copper washers “1”
• Rear brake hose “2”
• Rear brake hose union bolt “3”

WARNING

EWA1D77008

Proper brake hose routing is essential to in-
sure safe vehicle operation. Refer to “CABLE
ROUTING (for XV19S(C)/ XV19M(C)/
XV19CTS(C)/ XV19CTM(C))” on page 2-51
and “CABLE ROUTING (for XV19CS(C)/
XV19C(C))” on page 2-67.

CAUTION:

EC1D71009

When installing the brake hose onto the
brake master cylinder, make sure the brake
pipe touches the projection “a” on the brake
caliper bracket as shown.

2. Fill:

• Brake fluid reservoir

(with the specified amount of the recom-
mended brake fluid)

WARNING

EWA13090

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.

CAUTION:

ECA13540

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

3. Bleed:

• Brake system

Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-24.

4. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add the

recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-21.

Recommended fluid

DOT 4

T

R

.

.

Rear brake hose union bolt

30 Nm (3.0 m·kg, 22 ft·lb)

New

Recommended fluid

DOT 4

2

3

1

a

New

«
...
208
209
210
211
212
...
»

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

Freeride E-XC 2019

Brand: KTM Pages: 44

Brand: GAS GAS Pages: 119

EC-SIX DAYS - PART LIST 2011

Brand: GAS GAS Pages: 6

Brand: J&M Pages: 5

65175810022-00-40

Brand: hepco & becker Pages: 4

Brand: Suzuki Pages: 26

Brand: BMW Pages: 16

Brand: Isotta Pages: 2

WOLVERINE X4 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 224

Brand: Yamaha Pages: 343

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 432

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 694

Brand: Yamaha Pages: 864

Brand: Yamaha Pages: 912

Brand: Yamaha Pages: 864

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands