manualshive.com logo in svg

Yamaha XV19CTMX(C), Service Manual

The Yamaha XV19CTMX(C) Service Manual is a comprehensive guide for maintaining and repairing your motorcycle. This invaluable manual is available for free download at manualshive.com, providing detailed instructions and diagrams to ensure your bike is in top condition. Get the most out of your Yamaha with this essential manual.

Share
Download
background image

FUEL INJECTION SYSTEM

7-37

Sensor operation table

Er-1

No signals are received 
from the ECU.

• Open or short circuit in wire harness.
• Malfunction in meter.
• Malfunction in ECU.
• Defective wire connection of the ECU cou-

pler.

—

Er-2

No signals are received 
from the ECU within the 
specified duration.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Er-3

Data from the ECU cannot 
be received correctly.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Er-4

Non-registered data has 
been received from the 
meter.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Fault 
code 

No.

Symptom

Probable cause of malfunction

Diagnostic 

code No.

Diag-

nostic 

code 

No.

Item

Meter display

Checking method

01

Throttle angle

• Fully closed position

12–22

Check with throttle fully 
closed.

• Fully opened position

87–107

Check with throttle fully 
open.

03

Pressure difference
(atmospheric pressure and 
cylinder-#1 intake air pres-
sure)

Displays the cylinder-#1 in-
take air pressure.

Set the engine stop switch 
to “

”, and then push the 

start switch “

”. (If the dis-

play value changes, the 
performance is OK.)

04

Pressure difference
(atmospheric pressure and 
cylinder-#2 intake air pres-
sure)

Displays the cylinder-#2 in-
take air pressure.

Set the engine stop switch 
to “

”, and then push the 

start switch “

”. (If the dis-

play value changes, the 
performance is OK.)

05

Air temperature

Displays the air temperature.

Compare the actually mea-
sured air temperature with 
the meter display value.

07

Vehicle speed pulse

0–999

Check that the number in-
creases when the rear 
wheel is rotated. The num-
ber is cumulative and does 
not reset each time the 
wheel is stopped.

08

Lean angle sensor

Remove the lean angle 
sensor and incline it more 
than 65 degrees.

• Upright

0.4–1.4

• Overturned

3.7–4.4

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Brand: KTM Pages: 163
R&G CP0466 Series Fitting Instructions Manual preview
CP0466 Series
Brand: R&G Pages: 9
SCA 394021 Owner'S Instruction Manual preview
394021
Brand: SCA Pages: 5
Rekluse TorqDrive Clutch Pack Installation & User Manual preview
TorqDrive Clutch Pack
Brand: Rekluse Pages: 18
Royal Enfield SCRAM 411 2021 Owner'S Manual preview
SCRAM 411 2021
Brand: Royal Enfield Pages: 110
Shad NADSA W0CG62ST Manual preview
NADSA W0CG62ST
Brand: Shad Pages: 12
SHERCO 250 SE-R 2017 Workshop Manual preview
250 SE-R 2017
Brand: SHERCO Pages: 54
APRILIA ETV mille Caponord Use And Maintenance Book preview
ETV mille Caponord
Brand: APRILIA Pages: 384
Janus 250 Series Owner'S Handbook Manual preview
250 Series
Brand: Janus Pages: 96
KTM 58612027050 Mounting Instructions preview
58612027050
Brand: KTM Pages: 12
Baja DX110 Owner'S Manual preview
DX110
Brand: Baja Pages: 38
Indian Motorcycle 2884309 Installation Instructions preview
2884309
Brand: Indian Motorcycle Pages: 4
Royal Enfield Himalayan BS IV 2018 Owner'S Manual preview
Himalayan BS IV 2018
Brand: Royal Enfield Pages: 162
Royal Enfield CO Workshop Maintenance Manual preview
CO
Brand: Royal Enfield Pages: 52
Royal Enfield Continental GT Owner'S Manual preview
Continental GT
Brand: Royal Enfield Pages: 122
HealTech Electronics MM-T02 User Manual preview
MM-T02
Brand: HealTech Electronics Pages: 2
HealTech Electronics GIPRO GPXT Supplementary Manual preview
GIPRO GPXT
Brand: HealTech Electronics Pages: 2
HealTech Electronics Advanced Rider Assistant Manual preview
Advanced Rider Assistant
Brand: HealTech Electronics Pages: 4

Brands by name

Popular brands

Load more brands