Yamaha XV19CTMX(C) Service Manual Download Page 366 | Manualshive

Page: 366 / 494

background image

TRANSMISSION

5-117

3. Check:

• Transmission gears

Blue discoloration/pitting/wear

→

Replace

the defective gear(s).

• Transmission gear dogs

Cracks/damage/rounded edges

→

Replace

the defective gear(s).

4. Check:

• Transmission gear engagement

(each pinion gear to its respective wheel
gear)
Incorrect

→

Reassemble the transmission

axle assemblies.

5. Check:

• Transmission gear movement

Rough movement

→

Replace the defective

part(s).

6. Check:

• Circlips

Bends/damage/looseness

→

Replace.

ET1D71006

ASSEMBLING THE MAIN AXLE AND DRIVE
AXLE

1. Install:

• Toothed washer “1”

• Circlip “2”

NOTE:

• Be sure the circlip sharp-edged corner “a” is

positioned opposite side to the toothed washer
and gear. (for main axle)

• Install the circlip so that both ends “b” rest on

the sides of a spline “c” with both axles aligned.

2. Install:

• Toothed lock washer retainer “1”
• Toothed lock washer “2”

NOTE:

• With the toothed lock washer retainer “1” in the

groove “a” in the axle, align the projection “c”
on the retainer with an axle spline “b”, and then
install the toothed lock washer “2”.

• Be sure to align the projection on the toothed

lock washer that is between the alignment
marks “e” with the alignment mark “d” on the
retainer.

EAS26320

INSTALLING THE SHIFT FORKS AND SHIFT
DRUM ASSEMBLY

1. Install:

• Shift forks 1 “1”
• Shift fork 2 “2”
• Shift drum assembly “3”
• Shift fork guide bars “4”

New

1

2

2

New

a

b

c

2

e

e

d

b

c

1

c

b

a

2

1

«
...
364
365
366
367
368
...
»

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

Brand: hepco & becker Pages: 4

GearTronic ZERO GT3100-K1

Brand: PZRacing Pages: 2

Trekker Dolomiti

Brand: GIVI Pages: 24

Brand: Memphis Shades Pages: 2

Brand: Suzuki Pages: 26

Brand: GAS GAS Pages: 107

Brand: Puch Pages: 151

Brand: Wolfman Pages: 3

Brand: Honda Pages: 140

Brand: PUIG Pages: 2

Brand: hepco & becker Pages: 3

Brand: hepco & becker Pages: 4

Brand: CATU Pages: 6

Brand: CATU Pages: 8

Brand: APRILIA Pages: 216

gtrack 7855 MyBASIC

Brand: Gemini Pages: 20

Brand: Enerwatt Pages: 26

Brand: Malaguti Pages: 302

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands