Yamaha XV19CTMX(C) Service Manual Download Page 340

Page: 340 / 494

TRANSFER GEAR CASE

5-91

EAS25470

REMOVING THE MIDDLE DRIVEN SHAFT

NOTE:

Loosen the middle drive gear nut before remove
the drive pulley.

1. Install:

• Right rider footrest assembly

Refer to “ENGINE REMOVAL” on page 5-1.

2. Loosen:

• Middle drive gear nut “1”

NOTE:

When loosening the middle drive gear nut, press
down on the brake pedal so the middle drive
gear does not move.

3. Remove:

• Primary chain “1”
• Middle drive gear “2”
• Middle driven shaft “3”

NOTE:

Remove the primary chain, middle drive gear
and middle driven shaft at the same time.

EAS25480

CHECKING THE MIDDLE DRIVE

1. Check:

• Middle drive gear
• Middle driven gear

Damage/wear

→

Replace the middle drive

gear, middle driven shaft and primary chain
as a set.

2. Check:

• Primary chain

Damage/stiffness

→

Replace the primary

chain, middle drive gear and middle driven
shaft as a set.

EAS25490

CHECKING THE OIL STRAINER

1. Check:

• Oil strainer

Damage

→

Replace.

Contaminants

→

Clean with engine oil.

EAS25500

CHECKING THE TRANSFER GEAR OIL
PUMP

1. Check:

• Transfer gear oil pump housing
• Transfer gear oil pump cover

Cracks/damage/wear

→

Replace the defec-

tive part(s).

2. Measure:

• Inner-rotor-to-outer-rotor-tip clearance “a”
• Outer-rotor-to-oil-pump-housing clearance

“b”

• Oil-pump-housing-to-inner-rotor-and-outer-

rotor clearance “c”
Out of specification

→

Replace the transfer

gear oil pump.

1. Transfer gear oil pump inner rotor
2. Transfer gear oil pump outer rotor
3. Transfer gear oil pump housing

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands