Yamaha XV19CTMX(C) Service Manual Download Page 334

Page: 334 / 494

ELECTRIC STARTER

5-85

7. Check:

• Gear teeth

Damage/wear

→

Replace the gear.

8. Check:

• Bearings
• Oil seal

Damage/wear

→

Replace the defective

part(s).

EAS24800

ASSEMBLING THE STARTER MOTOR

1. Install:

• Starter motor yoke “1”

NOTE:

Align the projection “a” on the brush holder with
the slot “b” in the starter motor yoke.

2. Install:

• Starter motor front cover “1”

NOTE:

Align the match mark “a” on the starter motor
yoke with the match mark “b” on the starter mo-
tor front cover.

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands