Yamaha XV19CTMX(C) Service Manual Download Page 318

Page: 318 / 494

CLUTCH

5-69

EAS25260

INSTALLING THE CLUTCH

1. Install:

• Clutch housing
• Thrust washer

NOTE:

• Lubricate the clutch housing bearings with en-

gine oil.

• Make sure that the primary driven gear teeth

and primary drive gear teeth mesh correctly.

• Make sure that the primary driven gear teeth

and oil pump driven gear teeth mesh correctly.

2. Install:

• Clutch boss assembly “1”

NOTE:

• Install the clutch damper spring “2” with the

“OUTSIDE” mark facing out.

• If the wire circlip “3” has been removed, care-

fully install a new one.

3. Install:

• Clutch boss “1”

• Washer
• Conical spring washer “2”
• Clutch boss nut “3”

NOTE:

• Lubricate the clutch boss nut threads and con-

ical spring washer mating surfaces with engine
oil.

• Install the conical spring washer “2” with the

“OUT” mark “a” facing out.

• While holding the clutch boss with the univer-

sal clutch holder “4”, tighten the clutch boss
nut.

• Stake the clutch boss nut “3” at a cutout “b” in

the main axle.

4. Lubricate:

• Friction plates
• Clutch plates

(with the recommended lubricant)

5. Install:

• Friction plates 2 “1”
• Clutch plates
• Friction plate 1 “2”

NOTE:

• First, install a friction plate and then alternate

between a clutch plate and a friction plate.

• Align a projection on each friction plate 2 “1”

with the “

” mark “a” on the clutch housing

and align a projection on friction plate 1 “2” with
the punch mark “b” on the housing.

New

Clutch boss nut

105 Nm (10.5 m·kg, 75 ft·lb)

Universal clutch holder

90890-04086
YM-91042

Recommended lubricant

Engine oil

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands