Yamaha XV19CTMX(C) Service Manual Download Page 373 | Manualshive

Page: 373 / 494

background image

FUEL TANK

6-4

EAS26630

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank cap with a pump.

2. Remove:

• Fuel tank

CAUTION:

EC1D71021

Although the fuel has been removed from
the fuel tank, be careful when removing the
fuel hoses, since there may be fuel remain-
ing in them.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the fuel hose joint caps “1”.

NOTE:

After removing the fuel hose joint caps, clean the
projection on each cap so that no foreign mate-
rial will enter the fuel lines.

b. Lubricate the O-ring “1” with the recommend-

ed silicone lubricant “2”.

NOTE:

Spray the silicone lubricant in the areas shown in
the illustration.

c. Turn the screws “1” clockwise.

NOTE:

Turn the screws until they stop.

d. Disconnect the fuel hose (fuel hose joint to

fuel pump) “1” and air vent hose (fuel pump to
fuel hose joint) “2”.

NOTE:

Before removing the hoses, place a few rags in
the area under where they will be removed.

e. Install the fuel hose joint cap “1” and rubber

plug “2”.

NOTE:

Insert the projection on the fuel hose joint cap
completely into the pipe of the fuel hose joint and
insert the rubber plug into the end of the fuel
hose (fuel hose joint to fuel pump).

f. Remove the fuel tank.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS26640

REMOVING THE FUEL PUMP

1. Remove:

• Fuel hose connector cover

2. Disconnect:

• Fuel outlet hose

Recommended lubricant

Silicone protectant and lubri-
cant
ACC-SLCNS-PR-AY

1

2

1

1

1

2

1

1

2

«
...
371
372
373
374
375
...
»

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

Brand: Evotech Pages: 84

SBL.04.650.10000/B

Brand: SW-Motech Pages: 2

Brand: Honda Pages: 325

Splendor Pro CLASSIC

Brand: HERO Pages: 56

Brand: Salewa Pages: 17

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 388

Brand: Yamaha Pages: 18

Brand: VESPA Pages: 249

Brand: R&G Pages: 6

Brand: R&G Pages: 9

Brand: R&G Pages: 6

Brand: R&G Pages: 6

Brand: R&G Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands