Yamaha XV19CTMX(C) Service Manual Download Page 122 | Manualshive

Page: 122 / 494

background image

ENGINE

3-9

b. Turn the adjusting nut “2” in direction “a” or “b”

until the specified throttle cable free play is
obtained.

c. Tighten the locknut “1”.

WARNING

EWA12910

After adjusting the throttle cable free play,
start the engine and turn the handlebar to the
right and to the left to ensure that this does
not cause the engine idling speed to change.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS20680

CHECKING THE SPARK PLUGS

The following procedure applies to all of the
spark plugs.
1. Remove:

• Rider seat
• Rider seat bracket assembly

Refer to “GENERAL CHASSIS” on page 4-1.

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

• Air filter case

Refer to “GENERAL CHASSIS” on page 4-1.

2. Disconnect:

• Spark plug cap

3. Remove:

• Spark plug

CAUTION:

ECA13320

Before removing the spark plugs, blow away
any dirt accumulated in the spark plug wells
with compressed air to prevent it from falling
into the cylinders.

4. Check:

• Spark plug type

Incorrect

→

Change.

5. Check:

• Electrode “1”

Damage/wear

→

Replace the spark plug.

• Insulator “2”

Abnormal color

→

Replace the spark plug.

Normal color is medium-to-light tan.

6. Clean:

• Spark plug

(with a spark plug cleaner or wire brush)

7. Measure:

• Spark plug gap “a”

(with a wire thickness gauge)
Out of specification

→

Regap.

8. Install:

• Spark plug

NOTE:

Before installing the spark plug, clean the spark
plug and gasket surface.

9. Connect:

• Spark plug cap

10.Install:

• Air filter case

Refer to “GENERAL CHASSIS” on page 4-1.

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

• Rider seat bracket assembly
• Rider seat

Refer to “GENERAL CHASSIS” on page 4-1.

Direction “a”

Throttle cable free play is increased.

Direction “b”

Throttle cable free play is decreased.

a

b

1

2

Manufacturer/model

NGK/DPR8EA-9

Manufacturer/model

DENSO/X24EPR-U9

Spark plug gap

0.8–0.9 mm (0.031–0.035 in)

T

R

.

.

Spark plug

18 Nm (1.8 m·kg, 13 ft·lb)

«
...
120
121
122
123
124
...
»

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XV19CTMX(C)

Brand: GAS GAS Pages: 142

Advanced Million Color Mini Motorcycle Lighting Kit

Brand: LedGlow Pages: 3

Brand: R&G Pages: 12

Brand: GAS GAS Pages: 32

Brand: Insportline Pages: 19

Super Adventure 2016

Brand: KTM Pages: 25

Brand: Clas Ohlson Pages: 5

MULTISTRADA 1200S

Brand: Ducati Pages: 311

Brand: R&G Pages: 9

Brand: BMW Pages: 19

Brand: hepco & becker Pages: 2

Brand: Parkside Pages: 24

Brand: Parkside Pages: 109

Brand: KTM Pages: 20

Brand: Shad Pages: 2

Brand: Shad Pages: 2

Brand: Shad Pages: 2

Brand: Shad Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands