Yamaha XV19CTMX(C) Service Manual Download Page 199

Page: 199 / 494

FRONT BRAKE

4-46

• Turn the handlebar to the left and right to make

sure the brake hose does not touch other parts
(e.g., wire harness, cables, leads). Correct if
necessary.

3. Fill:

• Brake master cylinder reservoir

(with the specified amount of the recom-
mended brake fluid)

WARNING

EWA13540

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake master cylinder reser-
voir. Water will significantly lower the boil-
ing point of the brake fluid and could cause
vapor lock.

CAUTION:

ECA13540

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

4. Bleed:

• Brake system

Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-24.

5. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add the

recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-21.

6. Check:

• Brake lever operation

Soft or spongy feeling

→

Bleed the brake sys-

tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-24.

A. For XV19S(C)/ XV19M(C)/ XV19CTS(C)/

XV19CTM(C)

B. For XV19CS(C)/ XV19C(C)

Recommended fluid

DOT 4

10–30˚

15–35˚

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands