Yamaha XV19CTMX(C) Service Manual Download Page 317

Page: 317 / 494

CLUTCH

5-68

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

4. Install:

• Generator rotor

Refer to “INSTALLING THE GENERATOR”
on page 5-80.

5. Install:

• Left balancer drive gear “1”
• Left balancer idle gear “2”
• Left balancer driven gear “3”

NOTE:

• Align the punch mark “a” on the left balancer

drive gear with the punch mark “b” on the left
balancer idle gear.

• Align the punch marks “c” on the left balancer

idle gear with the punch marks “d” on the left
balancer driven gear.

6. Tighten:

• Left balancer drive gear bolt “1”

NOTE:

While holding the generator rotor “2” with the
sheave holder “3”, tighten the left balancer drive
gear bolt.

EAS25230

INSTALLING THE PRIMARY DRIVE GEAR

1. Install:

• Washer
• Straight key
• Primary drive gear
• Crankshaft position sensor rotor “1”
• Spacer
• Primary drive gear bolt “2”

CAUTION:

EC1D71007

The timing marks on the crankshaft position
sensor rotor must face outside.

NOTE:

• Lubricate the primary drive gear bolt threads

with engine oil.

• While holding the generator rotor “3” with the

sheave holder “4”, tighten the primary drive
gear bolt.

Left balancer drive gear bolt

40 Nm (4.0 m·kg, 29 ft·lb)

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

Primary drive gear bolt

100 Nm (10.0 m·kg, 72 ft·lb)

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands