Yamaha XV19CTMX(C) Service Manual Download Page 477

Page: 477 / 494

ELECTRICAL COMPONENTS

7-86

2. Check:

• Stator coil resistance

Out of specification

→

Replace the stator coil.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the pocket tester (

Ω

1) to the stator

coil coupler as shown.

b. Measure the stator coil resistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS28170

CHECKING THE RECTIFIER/REGULATOR

1. Check:

• Charging voltage

Out of specification

→

Replace the rectifi-

er/regulator.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Set the engine tachometer to the cylinder-#1

left spark plug lead or right spark plug lead.

b. Connect the pocket tester (DC 20 V) to the

rectifier/regulator coupler as shown.

c. Start the engine and let it run at approximate-

ly 5000 r/min.

d. Measure the charging voltage.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS28180

CHECKING THE HORNS

1. Check:

• Horn resistance

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Disconnect the horn 1 connectors and horn 2

coupler from the horn terminals.

b. Connect the pocket tester (

Ω

1) to the horn

terminals.

Stator coil resistance

0.112–0.168

Ω

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

white “1”

• Negative tester probe

→

white “2”

• Positive tester probe

→

white “1”

• Negative tester probe

→

white “3”

• Positive tester probe

→

white “2”

• Negative tester probe

→

white “3”

Charging voltage

14 V at 5000 r/min

2 3

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

red “1”

• Negative tester probe

→

black “2”

Coil resistance

0.94–0.98

Ω

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

horn terminal “1”

• Negative tester probe

→

horn terminal “2”

W W

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands