CABLE ROUTING (for XV19CS(C)/ XV19C(C))
2-72
1. EXUP servo motor
2. Fuse box
3. Wire harness
4. Fuel outlet hose
5. Cylinder-#1 right spark plug cap
6. Cylinder-#1 right ignition coil
7. Cylinder-#2 intake air pressure sensor coupler
8. Fuel sender (fuel tank) coupler
9. Meter assembly coupler
10. Front brake hose
11. Front turn signal/position light lead
12. Cylinder-#2 right spark plug cap
13. Cylinder-#2 right ignition coil
14. Rear brake light switch
15. Neutral switch lead
16. Stator coil lead
17. Speed sensor lead
18. EXUP cable
19. O
2
sensor lead
20. Cylinder-#1 right spark plug lead
A. Fasten the sub-wire harness with the holder.
B. Fasten the cylinder-#1 right spark plug lead, fuel
outlet hose, wire harness and the fuel tank damper
with a plastic locking tie. Install the plastic locking
tie in the rear slot of the fuel tank damper.
C. Fasten the fuel outlet hose, wire harness, and fuel
tank damper with a plastic locking tie. Install the
plastic locking tie in the front slot of the fuel tank
damper and make sure that the end of the damper
is aligned with the edge of the flat section on the
outside of the frame.
D. Fasten the wire harness to the guide on the engine
bracket (right upper side) with a plastic locking tie,
and then cut off the excess end of the tie.
E. Fasten the wire harness to the right ignition coil
bracket with a plastic locking tie.
F. Fasten the wire harness and meter assembly lead
to the frame with plastic locking ties. Face the end
of each plastic locking tie inward, and then cut off
the excess end of the tie.
G. Position the plastic locking tie to the front of the
projection on the frame.
H. Align the positioning tape on the wire harness with
the top of the frame.
I.
10 mm (0.39 in)
J. Fasten the front turn signal/position light leads to
the front brake hose with a plastic locking tie.
Position the buckle of the plastic locking tie to the
outside of the front brake hose, with the end of the
tie facing outward, and then cut off the excess end
of the tie.
K. Pass the wire harness through the guide.
L. Fasten the wire harness and cylinder-#2 right
spark plug lead to the frame with a plastic locking
tie. Face the end of the plastic locking tie
downward, and then cut off the excess end of the
tie.
M. To the throttle position sensor
N. To the fuel injectors and engine temperature
sensor
O. Fasten the stator coil lead with a plastic locking tie.
Position the buckle of the plastic locking tie to the
outside of the frame, with the end of the tie facing
downward, and then cut off the excess end of the
tie.
P. To the neutral switch
Q. To the speed sensor
R. Pass the O
2
sensor lead through the cutout in the
heat protector.
S. Outside of the frame
T. Inside of the frame
U. Position the buckle of the plastic locking tie to the
inside of the frame. Face the end of the plastic
locking tie upward, and then cut off the excess end
of the tie.
V. Position the buckle of the plastic locking tie to the
inside of the frame.
Summary of Contents for XV19CTMX(C)
