Yamaha XV19CTMX(C) Service Manual Download Page 278

Page: 278 / 494

CAMSHAFTS

5-29

4. Measure:

• Valve lifter case inside diameter “a”

Out of specification

→

Replace.

5. Calculate:

• Valve lifter-to-valve lifter case clearance

NOTE:

Calculate the clearance by subtracting the valve
lifter outside diameter from the valve lifter case
inside diameter.

Above 0.072 mm (0.0028 in)

→

Replace the

defective part(s).

EAS23930

CHECKING THE PUSH ROD COVER

1. Check:

• Push rod cover

Cranks/damage

→

Replace.

• Seal
• O-ring

Damage/wear

→

Replace the seal and O-

ring as a set.

EAS23980

CHECKING THE DECOMPRESSION SYSTEM

1. Check:

• Decompression system

NOTE:

• Check that the decompression pin “1” projects

from the camshaft.

• Check that the decompression cam “2” and de-

compression pin “1” moves smoothly.

2. Check:

• Decompression cam
• Decompression pin

Damage/wear

→

Replace.

ET1D71031

CHECKING THE DECOMPRESSION CAM
SPRING

The following procedure applies to all of the de-
compression cam springs.
1. Measure:

• Decompression cam spring free length “a”

Out of specification

→

Replace the decom-

pression cam spring.

Valve lifter outside diameter (in-
take)

22.962–22.974 mm (0.9040–
0.9045 in)

Valve lifter outside diameter (ex-
haust)

22.962–22.974 mm (0.9040–
0.9045 in)

Valve lifter hole inside diameter
(intake)

23.000–23.021 mm (0.9055–
0.9063 in)

Valve lifter hole inside diameter
(exhaust)

23.000–23.021 mm (0.9055–
0.9063 in)

Valve-lifter-to-valve-lifter-hole
clearance

0.026–0.059 mm (0.0010–0.0023
in)

Decompression cam spring

Free length

20.0 mm (0.79 in)

Limit

19.0 mm (0.75 in)

Summary of Contents for XV19CTMX(C)















































































































































































































































































































































































































































































































Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands

Yamaha XV19CTMX(C), Service Manual

Search results

Summary of Contents for XV19CTMX(C)

Reviews:

Related manuals for XV19CTMX(C)

Brands by name

Popular brands