Xtralis ADPRO FastTx Installation And User Manual Download Page 133 | Manualshive

Page: 133 / 138

background image

ADPRO FastTx by Xtralis

Installation and User Manual

Doc 11949_06

121

8 Specifications

8.1

ADPRO FastTx

An ADPRO FastTx system consists of one or more Multi-Site Video Security Systems at remote
sites and a PC running the ADPRO VideoCentral software at a monitoring site. Connection is via
a TCP/IP based Ethernet network, dial-up, leased telephone lines or ISDN.

Function

Description

Video inputs

Model AFTX-10 = 10 video inputs, Model AFTX-20 = 20 video inputs,

1 volt p/p video input, 75 ohm or high impedance, selectable via menu.

Colour / Monochrome Operation

Colour or monochrome. Default operation is for colour. Individual channels can be
selected as monochrome (B&W).

Video output

1 BNC composite video output designed to drive a 75-ohm load.

Video standard

Either PAL or NTSC (switch selectable).

Colourburst lock range

PAL 4.433619 MHz ± 230 Hz

NTSC 3.579545 MHZ ± 179 Hz

Grey Scale Resolution

256.

Video Compression Engine
(VCE)

AFTX-10 = 1 VCE module

AFTX-20 = 2 VCE modules

Image compression is via customised H.263 compression algorithm resulting in an
average of 3 KB per images at CIF resolution picture quality 6 and 6KB per image
at 2 CIF resolution picture quality 7.

Video Display modes at video
output

Full screen spot or sequence monitoring.

Image transmission rate

Typical transmission rates (subject to amount of scene activity):

Ethernet: 25 images per second

ISDN: 128 kbps = 12.5 images per second

PSTN 33.6 kbps = 3 images per second

Alarm inputs

Model AFTX-10: 20 alarm contact sensing or logic level inputs.
Model AFTX-20: 30 alarm contact sensing or logic level inputs.

Programmable to trigger an alarm on contact opening or closure.

All inputs have impedance >1 K ohm and transient protection >20 KV.

Single End-of-Line (SEOL) or Dual End-of-Line (DEOL) tamper detection on each
input.

Screw terminal connectors.

Voltage input less than 0.8 V = logic low, 7 mA (maximum).

Voltage input between 3.5 V and 5.0 V = logic high.

Minimum alarm contact duration = 100 milliseconds

Activity Detect Zones

The maximum activity detection area is defined by the number of available
detection zones:

396 zones (22 wide x 18 high) using CIF PAL resolution (352 x 288 pixels)

330 zones (22 wide x 15 high) using CIF NTSC resolution (352 x 240 pixels)

A detection zone represents a screen area of 16 x 16 pixels.

«
...
131
132
133
134
135
...
»

Summary of Contents for ADPRO FastTx











































































































































Reviews:

No comments

Related manuals for ADPRO FastTx

Brand: Manaras Opera Pages: 4

Brand: Samson Pages: 92

Brand: WDS Pages: 32

Brand: Michell Instruments Pages: 28

IC-F1000 series

Brand: Icom Pages: 2

Brand: LD Pages: 4

Brand: Omega Pages: 20

Brand: Jonsa Pages: 12

Brand: Galaxy Pages: 8

Brand: M-system Pages: 5

Brand: M-system Pages: 4

Brand: Danfoss Pages: 2

Brand: Wilmette Lighting Pages: 4

Brand: Williams Sound Pages: 2

Brand: Icom Pages: 36

Brand: Minebea Pages: 30

Brand: Orbit Merret Pages: 40

Brand: One for All Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands