manualshive.com logo in svg

Xerox D95, User Manual, Page: 184 / 460

Share
Download
Xerox D95 User Manual Download Page 184

Cause and Remedy

Fault code

Cause: Paper Tray 3 malfunctioned.
Remedy: Contact the Customer Support Center. Trays other than Paper Tray 3
can be used.

073-210

Cause: Paper Tray 4 malfunctioned.
Remedy: Contact the Customer Support Center. Trays other than Paper Tray 4
can be used.

074-210

Cause: Paper Tray 5 (bypass) malfunctioned.
Remedy: Power-cycle the machine. If the tray error is not fixed by performing the
relevant remedy, contact the Customer Support Center.

075-210
075-211

Cause: A “Pretransfer sensor ON” indicates a jam; this jam may be caused by any
of the following conditions: An error by the Pretransfer sensor, a worn fuser roll,
foreign material (such as paper) in the machine, or using media stock that is not
supported by the machine.
Remedy: Clear jammed paper.

077-142

Cause: Paper Tray 5 (Bypass) malfunctioned.
Remedy: Power-cycle the machine. If the tray errors are not fixed by performing
the relevant remedy, contact the Customer Support Center.

078-213
078-214
078-282
078-283

Check the paper loaded in Tray 5 and then power off/on the printer.

078-281

Power off/on the printer.

078-282

Cause: Charge Corotron cleaner failure.
Remedy: Power-cycle the machine. If the error is not fixed by performing the
relevant remedy, contact the Customer Support Center.

091-311

Cause: Charge Corotron fault.
Remedy: Power off/on the machine.

091-320

Cause: 2 sided print could not be made.
Remedy: Print each side separately.

116-701

Cause: Printing was performed using a substitute font.
Remedy: Check the print data.

116-702

Cause: An error occurred during PostScript processing.
Remedy: Either confirm the print data or click Spool Settings on the Details tab in
the print driver to set bi-directional communications to off.

116-703

Cause: A probable cause is that the correct document size could not be judged as
the receive data exceeded the HP-GL/2 spool size.
Remedy: Increase the size assigned to HP-GL/2 auto-layout memory.

116-710

Cause: Job was divided and printed due to insufficient disk space.
Remedy: Remove unnecessary data from the hard disk to increase free disk space.

116-713

Cause: An HP-GL/2 command error occurred.
Remedy: Check the print data.

116-714

Cause: An error occurred during printing as there was insufficient memory.
Remedy: Stop unnecessary ports and remove unnecessary data from the hard disk
to increase free disk space.

116-720

User Guide

15-26

Problem solving

Summary of Contents for D95













































































































































































































































































































































































































































































Reviews:

No comments