VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 242 / 317

Front brake calliper

Removal

- Remove the front wheel

- Pre-loosen the two fixing pins of the brake pads

- Remove the two front brake calliper devices fas-

tening them to the support as shown in the photo-

graph.

N.B.

WHEN A PROCEDURE IS PLANNED INCLUDING THE
SERVICE OR REPLACEMENT OF THE CALLIPER, FIRST
LOOSEN THE FITTING CONNECTING THE PIPE TO THE
BRAKE CALLIPER

Overhaul

Proceed as follows:

1) remove the two male hexagonal screws (1) and

take out the two pads (10);

2) remove the two male hexagonal screws (2) and

remove the reaction plate (3);

3) take out the fixed plate (4) from the guide;

4) remove the internal elements from the floating

body (5) with the help of short blows of com-

pressed air through the brake fluid pipe in order to

facilitate the expulsion of pistons (6).

5) Check:

- that the plates and the body are whole and in

good condition;

Braking system

Vespa GTS Super 300 ie (2008)

BRAK SYS - 242

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands