VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 134

Page: 134 / 317

- Lock the driven pulley again using the specific

tool.

- Preload the clutch return spring with a traction/

rotation combined action and place the belt in the

smaller diameter rolling position.

- Remove the driven pulley /belt unit from the tool.

N.B.

DURING THE SPRING PRELOADING PHASE, BE CARE-
FUL NOT TO DAMAGE THE PLASTIC SPRING STOP AND
THE BUSHING THREADING.

N.B.

FOR DESIGN REASONS, THE NUT IS SLIGHTLY ASYM-
METRIC; THE FLATTEST SURFACE SHOULD BE MOUN-
TED IN CONTACT WITH THE CLUTCH.

Specific tooling

020444Y

Tool for fitting/ removing the driven

pulley clutch

020444Y011

adapter ring

020444Y009

wrench 46 x 55

Locking torques (N*m)

Clutch unit nut on driven pulley

45 ÷ 50

Refitting the driven pulley

- Refit the clutch bell.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 134

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands