VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 152 / 317

- Loosen the central screw on the tensioner first.

- Remove the two fixings shown in the figure.

- Remove the tensioner with its gasket.

- Remove the internal hex screw and the counter-

weight shown in the figure.

- Remove the camshaft control pulley with its

washer.

- Remove the control sprocket wheel and the tim-

ing chain.

- Remove the screws indicated in the figure, the

spacer bar and the tensioner slider.

The chain tensioner slider must be removed from

the transmission side. As regards the lower chain

guide slider, it may only be removed after the head

has been removed.

N.B.

IT IS ADVISABLE TO MARK THE CHAIN IN ORDER TO EN-
SURE THAT THE INITIAL DIRECTION OF ROTATION IS
MAINTAINED.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 152

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands