VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 209 / 317

Check the power supply line of the injection load

solenoid energising coil: after switching to "ON",

make sure there is battery voltage, for two sec-

onds, between the Red-White cable and Black-

Purple cable of the solenoid control base. If there

is not, check the continuity of the Red-White cable

between the fuse box under the saddle hinge and

the remote control base and of the Black-Purple

cable between pin 22 of the control unit and the

remote control base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT WITH THE
COMPONENTS DISCONNECTED. (RELAYS, CONTROL
UNIT, FUSES ETC.).

Vespa GTS Super 300 ie (2008)

Injection

INJEC - 209

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands