VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 146

Page: 146 / 317

Refitting the stator

- Refit the stator and flywheel carrying out the re-

moval procedure in reverse, tightening the retain-

ers to the specified torque.

Locking torques (N*m)

Stator assembly screws (°)

3 to 4

Refitting the flywheel cover

- Position the spline clip on the crankshaft and ori-

ent the end as shown in the figure.

- Orient the water pump shaft with reference to the

transmission gear seat as shown in the picture.

- Refit the cover over the engine and tighten the screws to the prescribed torque.

- Carry out the removal steps but in the reverse order.

CAUTION

TAKE CARE TO CORRECTLY POSITION THE FLYWHEEL CONNECTOR. MAKE SURE THE CEN-
TRING DOWELS ARE PRESENT.

Locking torques (N*m)

Flywheel cover screws

11 - 13

Flywheel and starting

Engine

Vespa GTS Super 300 ie (2008)

ENG - 146

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands