VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 90 / 317

Diagnostic code - 1 flash

A one-flash code indicates a system where the se-

rial line is not present or is not detected. Check the

Immobilizer antenna wiring and change it if nec-

essary.

Diagnostic code - 2 flashes

A two-flash code shows a system where the con-

trol unit does not show the transponder signal. This

might depend on the inefficiency of the immobilizer

antenna or the transponder.

Turn the switch to ON using several keys: if the

code is repeated even with the Master key, check

the aerial wiring and change it if necessary. If this

is not the case, replace the defective key and/or

reprogram the control unit. Replace the control unit

if the problem continues.

Diagnostic code - 3 flashes

A three-flash code indicates a system where the

control unit does not recognise the key. Turn the

switch to ON using several keys: if the error code

is repeated even with the Master key, replace the

control unit. If this is not the case, reprogram the

decoder.

Battery recharge circuit

The charging circuit consists of three-phase alternator and a permanent magneto flywheel.

The generator is directly connected to the voltage regulator.

This, in its turn, is connected directly to the ground and the battery positive terminal passing through

the 30A protective fuse.

Electrical system

Vespa GTS Super 300 ie (2008)

ELE SYS - 90

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands