manualshive.com logo in svg

VESPA GTS Super 300 ie 2008, Service Station Manual

The VESPA GTS Super 300 ie 2008 is a powerful and stylish scooter designed for urban commuting. To ensure its optimal performance and longevity, it is essential to have a comprehensive Service Station Manual. You can conveniently download this manual for free from our website, manualshive.com.

Share
Download
background image

- By means of the table, see the Specifications chapter identify the cylinder base gasket thickness to

be used for refitting. Correctly identify the cylinder base gasket thickness to keep the correct compres-

sion ratio.

- Remove the special tool and the cylinder.

N.B.

IF DEVIATIONS (OR RECESSES OR PROJECTIONS) CLOSE TO THE CHANGE OF CATEGORY
ARE MEASURED, REPEAT THE MEASUREMENT AT THE OPPOSED SIDE. TO DO SO, REPEAT
THE TOOL INSTALLATION BY INVERTING ITS POSITION.

See also

Slot packing system

Refitting the piston rings

- Place the scraper ring spring on the piston.

- Install the scraper ring keeping the opening op-

posed to the spring junction and with the writing

"top" facing the piston crown. The chamfered side

of the oil scraper ring should always be facing the

piston crown.

- Fit the second lining with the identification letter

or the writing "top" facing the piston crown. In any

case, the step must be facing opposite the piston

crown.

- Install the first compression lining in the direction

imposed by the housing.

- It is advisable to use a fitter to facilitate the in-

stallation of the linings.

N.B.

THE TWO PISTON RINGS ARE MADE WITH A TAPERED
CYLINDRICAL CONTACT CROSS-SECTION. THIS IS TO
ACHIEVE A BETTER BEDDING.

- Misalign the lining openings at 120° as shown in the figure.

- Lubricate the components with engine oil.

- The engine uses the first compression lining with an L section.

Vespa GTS Super 300 ie (2008)

Engine

ENG - 157

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Reviews:

No comments

Related manuals for GTS Super 300 ie 2008

Razor A5 DLX Manual preview
A5 DLX
Brand: Razor Pages: 32
W-Tec Teneur 10 User Manual preview
Teneur 10
Brand: W-Tec Pages: 14
Reel Performance + User Manual preview
Performance +
Brand: Reel Pages: 20
WHEELS FOR FEET GO GO ELITE Instructions And Manuallines preview
GO GO ELITE
Brand: WHEELS FOR FEET Pages: 4
Wheela Standard Edition User And Safety Manual preview
Standard Edition
Brand: Wheela Pages: 7
Viro Rides VR 550E Quick Start Manual preview
VR 550E
Brand: Viro Rides Pages: 2
BMS SOLANO 50 RX Owner'S Manual preview
SOLANO 50 RX
Brand: BMS Pages: 48
KOMFI-RIDER Globe Trotter User Manual preview
Globe Trotter
Brand: KOMFI-RIDER Pages: 28
Okayrobot G4T series User Manual preview
G4T series
Brand: Okayrobot Pages: 62
X-TREME XR-302 Product Handbook preview
XR-302
Brand: X-TREME Pages: 12
EOVOLT Confort Manual preview
Confort
Brand: EOVOLT Pages: 24
kikkaride DUSTY Instructions For Use Manual preview
DUSTY
Brand: kikkaride Pages: 23
Yamaha YP125R Service Manual preview
YP125R
Brand: Yamaha Pages: 498
Xiaomi MiScoot Pro2 Ed AMG Manual preview
MiScoot Pro2 Ed AMG
Brand: Xiaomi Pages: 84
Land Pride 710-040M Operation Manual preview
710-040M
Brand: Land Pride Pages: 44
EasyTravel ET1L User Manual preview
ET1L
Brand: EasyTravel Pages: 24
Zipr Mantis PC Owner'S Manual preview
Mantis PC
Brand: Zipr Pages: 25
DAXYS LIZARD User Manual preview
LIZARD
Brand: DAXYS Pages: 28

Brands by name

Popular brands

Load more brands