manualshive.com logo in svg

VESPA GTS Super 300 ie 2008, Service Station Manual

The VESPA GTS Super 300 ie 2008 is a powerful and stylish scooter designed for urban commuting. To ensure its optimal performance and longevity, it is essential to have a comprehensive Service Station Manual. You can conveniently download this manual for free from our website, manualshive.com.

Share
Download
background image

inside the cylinder, the less the base gasket to be applied (to recover the compression ratio) and vice

versa.

N.B.

MEASUREMENT "A" MUST BE TAKEN WITHOUT ANY GASKET FITTED BETWEEN THE CRANK-
CASE AND CYLINDER AND AFTER RESETTING THE DIAL GAUGE, EQUIPPED WITH A SUP-
PORT, ON A GROUND PLANE

ENGINE 300 SHIMMING

Name

Measure A

Thickness

SHIMMING

3.70 - 3.60

0.4 ± 0.05

SHIMMING

3.60 - 3.40

0.6 ± 0.05

SHIMMING

3.40 - 3.30

0.8 ± 0.05

Products

RECOMMENDED PRODUCTS TABLE

Product

Description

Specifications

AGIP GEAR SAE 80W-90

Lubricant for gearboxes and transmis-

sions.

API GL-4

eni i-Ride PG 5W-40

Synthetic based lubricant for high-per-

formance four-stroke engines.

JASO MA, MA2 - API SL - ACEA A3

AGIP FILTER OIL

Special product for the treatment of foam

filters.

-

AGIP GP 330

Water repellent stringy calcium spray

grease.

R.I.D./A.D.R. 2 10°b) 2 R.I.Na. 2.42 -
I.A.T.A. 2 - I.M.D.G. class 2 UN 1950

Page 9022 EM 25-89

eni i-Ride PG 5W-40

Synthetic based lubricant for high-per-

formance four-stroke engines.

JASO MA, MA2 - API SL - ACEA A3

AGIP BRAKE 4

Brake fluid.

Synthetic fluid SAE J 1703 -FMVSS 116

- DOT 3/4 - ISO 4925 - CUNA NC 956

DOT 4

AGIP PERMANENT SPEZIAL

Ethylene glycol-based antifreeze fluid

with organic inhibition additives. Red,

ready to use.

ASTM D 3306 - ASTM D 4656 - ASTM D

4985 - CUNA NC 956-16

AGIP GREASE PV2

Ivory smooth-textured, slightly-stringy

anhydrous calcium-base grease.

TL 9150 066, NATO G 460 symbol

Vespa GTS Super 300 ie (2008)

Characteristics

CHAR - 31

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Reviews:

No comments

Related manuals for GTS Super 300 ie 2008

Rascal Vecta Sport Owners Manual & Service Record preview
Vecta Sport
Brand: Rascal Pages: 32
C.T.M. HS-928 Service Manual preview
HS-928
Brand: C.T.M. Pages: 47
HARTJE ESILENTIO User Manual preview
ESILENTIO
Brand: HARTJE Pages: 38
Hudora Kick Wheel 11050 Instructions On Assembly And Use preview
Kick Wheel 11050
Brand: Hudora Pages: 8
Nova Cruz Voloci User Manual preview
Voloci
Brand: Nova Cruz Pages: 13
Texas Comfort 125-4X User Manual preview
Comfort 125-4X
Brand: Texas Pages: 33
Lambretta 150 ld User Manual preview
150 ld
Brand: Lambretta Pages: 68
Golden Companion Service Manual preview
Companion
Brand: Golden Pages: 29
Golden GB-106 Buzzaround Lite Owner'S Manual preview
GB-106 Buzzaround Lite
Brand: Golden Pages: 40
FREERIDER Luggie Classic User Instruction Manual preview
Luggie Classic
Brand: FREERIDER Pages: 48
Gilis Bebe Stars Aero User Manual preview
Bebe Stars Aero
Brand: Gilis Pages: 8
Gilis BebeStars Isporter User Manual preview
BebeStars Isporter
Brand: Gilis Pages: 8
KUGOO G-Booster User Manual preview
G-Booster
Brand: KUGOO Pages: 18
Lacros Trotter T200 Translation Of The Original Instruction preview
Trotter T200
Brand: Lacros Pages: 16
Jamara KickLight Instruction preview
KickLight
Brand: Jamara Pages: 4
UJET UJET User Manual preview
UJET
Brand: UJET Pages: 116
BLUETOUCH BT350 Instruction Manual preview
BT350
Brand: BLUETOUCH Pages: 73
Jeep JE-MX27.5+ User Manual - Original Instructions preview
JE-MX27.5+
Brand: Jeep Pages: 88

Brands by name

Popular brands

Load more brands