VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 247

Page: 247 / 317

Removal

- Remove the front wheel

- Pre-loosen the two fixing pins of the brake pads

- Remove the brake calliper

- Remove permanently the two pad fixing screws

- Check that there are no flaws or warping. If there

is, replace it.

- Check the thickness of the friction material is

more than 1.5 mm. If it is not, replace it

- The replacement must be made with greater re-

sidual thickness if the pad has not worn evenly. A

0.5 mm thickness difference in the residual friction

material is permitted

Refitting

To fit, proceed as follows:

- Insert the two pads in the callipers.

Vespa GTS Super 300 ie (2008)

Braking system

BRAK SYS - 247

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands