VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 160

Page: 160 / 317

COLOUR ON COTTER SIDE (TURNS WITH GREATER
PITCH).

Specific tooling

020306Y

Punch for assembling valve seal

rings

020382Y

Valve cotters equipped with part 012

removal tool

020382Y011

adapter for valve removal tool

Inspecting the cam shaft

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Cylinder Head

Refitting the head and timing system components

- Refit the lower timing chain sprocket wheel on the

crankshaft, with the chamfer facing the insertion

side.

- Loop the timing chain around the sprocket on the

crankshaft.

- Fit the chain tensioner slider from the cylinder

head side.

- Fit the spacer and the screw fastener.

- Tighten the screws to the prescribed torque.

- Fit the pins and rocking levers.

- Lubricate the two rocking levers through the

holes at the top.

- Lubricate the 2 bearings and insert the camshaft

in the cylinder head with the cams corresponding

to the rocking levers.

- Insert the retention plate and tighten the two

screws shown in the figure to the prescribed tor-

que.

- Refit the spacer on the camshaft.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 160

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands