VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 156 / 317

Removing the piston

- Install piston and wrist pin onto the connecting

rod, aligning the piston arrow the arrow facing to-

wards the exhaust.

- Fit the wrist pin retainer ring onto the appropriate

tool

- With opening in the position indicated on the tool

S = left

D= right

- Place the wrist pin retainer ring into position using

a punch

- Fit the wrist pin snap ring using the plug as shown

in the figure

N.B.

THE TOOL FOR INSTALLING THE RETAINER RINGS MUST
BE USED MANUALLY.

CAUTION

USING A HAMMER MIGHT DAMAGE THE STOPS' HOUS-
ING.

Specific tooling

020454Y

Pin lock fitting tool

Choosing the gasket

- Provisionally fit the piston into the cylinder, without any base gasket.

- Assemble a dial gauge on the specific tool.

Specific tooling

020428Y

Piston position check mounting

- Using an abutment plane, reset the dial gauge

with a preload of a few millimetres.

- Finally fix the dial gauge.

- Check the perfect sliding of the feeler pin.

- Install the tool on the cylinder without changing

the dial gauge position.

- Lock the tool using the original head fixing nuts.

- Rotate the crankshaft up to the TDC (the inver-

sion point of the dial gauge rotation)

- Measure the deviation from the reset value.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 156

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands