manualshive.com logo in svg

VESPA GTS Super 300 ie 2008, Service Station Manual

The VESPA GTS Super 300 ie 2008 is a powerful and stylish scooter designed for urban commuting. To ensure its optimal performance and longevity, it is essential to have a comprehensive Service Station Manual. You can conveniently download this manual for free from our website, manualshive.com.

Share
Download
background image

COIL

Function

Allows generation of the electrical discharge on

the spark plug, with an increase of voltage.

Pinout:

1. Power from relay

2. Activation by control unit (control unit side PIN

1)

ELECTRICAL ERRORS

H.V. Coil

 P0351 - shorted to positive / open circuit or shorted to negative.

Error cause

Shorted to positive: excessive voltage at PIN 1 of the control unit connector.

Circuit open or short circuit to negative:interruption of the circuit or null voltage at PIN 1 of the control

unit connector.

Troubleshooting

Short circuit to positive:

- Disconnect the coil connector, turn the key to ON and activate the component through the diagnostics

instrument.

- Verify the presence of voltage on the coil connector PIN 2: if present, restore the cabling, otherwise

replace the coil.

Open circuit:

- Carry out the check procedure of the coil and control unit connectors.

- Verify continuity of the cabling between the coil and control unit: Coil PIN 2 - control unit PIN 1. If there

is no continuity, restore the cable harness.

- Verify, with the key turned ON, the presence of voltage on the coil connector PIN 1. If no voltage is

detected, check that the cable harness between the coil and injection relay is not interrupted: PIN 1 coil

- relay.

- If the above tests provided a positive result, the coil should be replaced.

Short circuit to negative:

- Disconnect the control unit connector and the coil connector.

- Verify the coil connector PIN 2 ground insulation (or control unit connector PIN 1). If necessary, restore

the cable harness.

Vespa GTS Super 300 ie (2008)

Electrical system

ELE SYS - 109

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Reviews:

No comments

Related manuals for GTS Super 300 ie 2008

RACCEWAY KOBRA User Manual preview
KOBRA
Brand: RACCEWAY Pages: 105
Easy Wheels MCE-18412 User Manual preview
MCE-18412
Brand: Easy Wheels Pages: 21
MEGAWHEELS S10 User Manual preview
S10
Brand: MEGAWHEELS Pages: 80
Exclusive Brands Smart Glider Manual preview
Smart Glider
Brand: Exclusive Brands Pages: 16
CPI Aragon 125 Manual preview
Aragon 125
Brand: CPI Pages: 15
Xtracycle 2016 EdgeRunner User Manual preview
2016 EdgeRunner
Brand: Xtracycle Pages: 30
TilGreen Coopop TilChap Original User Manual preview
Coopop TilChap
Brand: TilGreen Pages: 65
CareCo victory Owner'S Manual preview
victory
Brand: CareCo Pages: 30
Golden Companion I Owner'S Manual preview
Companion I
Brand: Golden Pages: 40
Golden LiteRider GL111 Owner'S Manual preview
LiteRider GL111
Brand: Golden Pages: 42
Golden Buzzaround XL GB117HD Owner'S Manual preview
Buzzaround XL GB117HD
Brand: Golden Pages: 44
SunL SL150-18 Manual preview
SL150-18
Brand: SunL Pages: 23
Shoprider FLAGSHIP TE-889XLSN User Manual preview
FLAGSHIP TE-889XLSN
Brand: Shoprider Pages: 16
Lacros AMBLING A200 Original Manual preview
AMBLING A200
Brand: Lacros Pages: 16
Vermeiren Alya User Manual preview
Alya
Brand: Vermeiren Pages: 164
DAELIM HISTORY 125 - SERVICE Service Manual preview
HISTORY 125 - SERVICE
Brand: DAELIM Pages: 208
KBO Breeze Owner'S Manual preview
Breeze
Brand: KBO Pages: 22
3Style Scooters RGS-2 Instructions & Care Manual preview
RGS-2
Brand: 3Style Scooters Pages: 36

Brands by name

Popular brands

Load more brands