VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 270

Page: 270 / 317

Front mudguard

- First remove the steering tube and uncouple the

front brake pipes from the calliper in order to re-

move the front mudguard

- Remove the three mudguard-steering tube

clamps indicated in the figure

Radiator fan

- In order to carry out any operation on the radiator

unit, flow out the coolant in the coolant delivery

pipe in the pump, indicated in the photograph.

- Remove the shield back plate;

- Remove the coolant feed and return hoses from

the right radiator;

- Unscrew the 4 screws fixing the radiator to the

body;

- Detach the radiator

- Detach the pipe from the plastic duct by removing

the plastic clip shown in the photograph. Then re-

move the duct.

Chassis

Vespa GTS Super 300 ie (2008)

CHAS - 270

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands