VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 175 / 317

- Check the clearance between the rotors in the

position shown in the diagram using a feeler

gauge.

Measure the distance between the outer rotor and

the pump body (see figure).

- Check the axial clearance of the rotors using a

trued bar as shown in the figure.

Characteristic

Axial rotor clearance

Limit values admitted: 0.09 mm

Distance between the outer rotor and the pump
body

Admissible limit clearance: 0.20 mm

Distance between the rotors

Admissible limit clearance: 0.12 mm

Refitting

- Check there are no signs of wear on the oil pump

shaft or body.

- Check there are no signs of scoring or wear on

the oil pump cover.

- If you detect non-conforming measurements or

scoring, replace the faulty parts or the unit.

- Fit the pump cover in the position that permits the

crankcase clamping screws to be aligned.

- Make sure the gasket is positioned properly and

refit the pump on the engine crankcase. The pump

can only be fitted in one position. - Tighten the

screws to the prescribed torque.

Vespa GTS Super 300 ie (2008)

Engine

ENG - 175

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands