VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 183 / 317

: Fuel system

a. Faulty fuel pump

b.Dirty fuel filter

: Ignition system

a. Faulty spark plug

b.Faulty coil

c.Faulty screened cap

: Intake circuit

a. Air filter dirty

b.Dirty by-pass circuit

c.Faulty stepper motor

: Other

a. Wrong distribution timing

b.Incorrect idle speed carburetion

c.Incorrect reset of the throttle valve position sensor

2 MIU system faults may be caused by loose connectors. Make sure that all connections have been

correctly made.

Check the connectors taking into consideration the following point:

check that the terminals are not bent.

check that the connectors have been properly connected.

- Check whether the malfunction can be fixed by shaking the connector slightly.

3 Check the entire system before replacing the MIUIf the fault is fixed by replacing the MIU, install the

original control unit again and check if the fault occurs again.

4 Use a multimeter with an internal resistance of more than 10K Ohm /V when troubleshooting. Instru-

ments that are not suitable might damage the MIU central control unit. Use instruments with definitions

over 0.1V and 0.5 W , the precision must be greater than 2%.

Terminals setup

ELECTRONIC CONTROL UNIT CONNECTOR

. H.V. COIL (Pink-Black)

Vespa GTS Super 300 ie (2008)

Injection

INJEC - 183

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands