VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 143 / 317

Refitting the hub cover bearings

In order to fit the hub box bearings, the engine

crankcase and the cover must be heated with the

special heat gun.

- The three 15-mm bearings must be fitted using

the appropriate tools:

- The 42-mm side of the adapter must be turned

towards the bearing.

Specific tooling

020150Y

Air heater mounting

020151Y

Air heater

020376Y

Adaptor handle

020359Y

42 x 47-mm Adaptor

020412Y

15-mm guide

N.B.

TO FIT THE BEARING ON THE COVER, ADEQUATELY SUPPORT THE COVER WITH THE STUD
BOLT KIT.

- Refit the driven pulley shaft bearing with a mod-

ular punch as shown in the figure.

N.B.

IF THE BEARING HAS AN ASYMMETRICAL BALL RETAIN-
ER, PLACE IT SO THAT THE BALLS ARE VISIBLE FROM
THE HUB INNER SIDE.

Specific tooling

020376Y

Adaptor handle

020359Y

42 x 47-mm Adaptor

020363Y

20-mm guide

N.B.

WHEN FITTING THE BEARINGS ON THE ENGINE CRANKCASE, SUPPORT THE CRANKCASE
PREFERABLY ON A SURFACE TO ALLOW THE BEARINGS TO BE DRIVEN VERTICALLY.

- Refit the Seeger ring with the opening facing the bearing and fit a new oil seal flush with the crankcase

from the pulley side.

Vespa GTS Super 300 ie (2008)

Engine

ENG - 143

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands