manualshive.com logo in svg

VESPA GTS Super 300 ie 2008, Service Station Manual

The VESPA GTS Super 300 ie 2008 is a powerful and stylish scooter designed for urban commuting. To ensure its optimal performance and longevity, it is essential to have a comprehensive Service Station Manual. You can conveniently download this manual for free from our website, manualshive.com.

Share
Download
background image

Crankcase - crankshaft

Splitting the crankcase halves

- Before opening the crankcase, it is advisable to

check the axial clearance of the crankshaft. To do

this, use a plate and a support with appropriate tool

dial gauge.

- Upper clearances are an indication of wear on

the surfaces of the crankshaft casing support.

- Remove the 10 crankshaft coupling screws.

- Separate the crankcase while keeping the crank-

shaft in one of the two halves of the crankcase.

- Remove the crankshaft.

- Remove the half crankcase coupling gasket.

- Remove the two screws and the internal cover

shown in the diagram.

- Remove the oil guard on the flywheel side.

- Remove the oil filter fitting shown in the diagram.

- Check the axial clearance on the connecting rod.

- Check the radial clearance on the connecting rod.

-Check the surfaces that limit the axial free-play

are not scored and measure the width of the crank-

shaft between these surfaces, as shown in the

diagram.

- If the axial clearance between crankshaft and

crankcase is exceeding and the crankshaft does

not have any defect, the problem must be due to

either excessive wear or wrong machining on the

crankcase.

- Check the diameters of both the bearings of the

crankshaft in accordance with the axes and surfa-

ces shown in the figure. The half-shafts are clas-

sified in two categories Cat. 1 and Cat. 2 as shown

the chart below.

CAUTION

THE CRANKSHAFT CAN BE REUSED WHEN THE WIDTH
IS WITHIN THE STANDARD VALUES AND THE SURFACES
SHOW NO SIGNS OF SCORING.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 164

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Reviews:

No comments

Related manuals for GTS Super 300 ie 2008

DAELIM BESBI - Brochure preview
BESBI -
Brand: DAELIM Pages: 2
KYBURZ DXP 4.0 Operating Manual preview
DXP 4.0
Brand: KYBURZ Pages: 22
Skoot-Eze TBSC79020 User Manual preview
TBSC79020
Brand: Skoot-Eze Pages: 12
myToys 205 Information Manual preview
205
Brand: myToys Pages: 10
Yedoo Mau New User Manual preview
Mau New
Brand: Yedoo Pages: 19
Roketa Moto Fino MF125QT-7 Manual preview
Moto Fino MF125QT-7
Brand: Roketa Pages: 30
VESPA LX 125ie 3Valvole Manual preview
LX 125ie 3Valvole
Brand: VESPA Pages: 94
E Rider RONDO User Manual preview
RONDO
Brand: E Rider Pages: 9
Rider 30 MODA User Manual preview
30 MODA
Brand: Rider Pages: 10
X-TREME XM-5000Li Operation And Maintenance Instructions preview
XM-5000Li
Brand: X-TREME Pages: 21
X-TREME XMB-400 Owner'S Manual preview
XMB-400
Brand: X-TREME Pages: 34
KUGOO B1 Instructions Manual preview
B1
Brand: KUGOO Pages: 35
Streamline Seats Vento short Assembly Instruction preview
Vento short
Brand: Streamline Seats Pages: 2
Streamline Seats Pace Assembly Instructions preview
Pace
Brand: Streamline Seats Pages: 2
ROBOR SMART-C User Manual preview
SMART-C
Brand: ROBOR Pages: 23
E-TON MATRIX PN2H 50CC Installation preview
MATRIX PN2H 50CC
Brand: E-TON Pages: 2
Nipponia Neon Owner'S Manual preview
Neon
Brand: Nipponia Pages: 38
Nipponia Volty Owner'S Manual preview
Volty
Brand: Nipponia Pages: 54

Brands by name

Popular brands

Load more brands