VESPA GTS Super 300 ie 2008 Service Station Manual Download

Page: 224 / 317

- Once the pin has been fitted, insert the two

spacers part 17 slightly hitting with a mallet (see

next figure).

CAUTION

USE NEW ROLLER CASINGS, PIN, SEALING RINGS AND
DUST GUARDS FOR REFITTING.

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Ivory smooth-textured,

slightly-stringy anhydrous calcium-base
grease.

TL 9150 066, NATO G 460 symbol

To fit sealing rings, roller casings and wedging

washers proceed as follows

- Lubricate the sealing rings with mineral oil and

half-fill the roller casings with recommended

grease.

- Insert the sealing ring on the pin and the roller

bushing with wedging washers at the same time.

- Remove the specific tool and then the part 5

(guide) partially ejected in the previous assembly

stage; part 4 must be always fitted.

- Replace part 3 with part 16 on the stem.

- Push, from the handgrip, the wedging washer -

roller casing - sealing ring unit, placing part 16 until

it stops on the swinging hub

- Repeat the operation described above using the

tool fitted with part 16 and part 22* instead of part

4 on the stem, on the side opposite the one shown

in the figure to refit the second wedging washer -

roller casing - sealing ring unit.

Suspensions

Vespa GTS Super 300 ie (2008)

SUSP - 224

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands