VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 127

Page: 127 / 317

Inspecting the clutch drum

- Check that the clutch bell is not worn or damaged.

- Measure the clutch bell inside diameter.

Characteristic

Max. value clutch housing

Max. value: Ø 134.5 mm

clutch housing standard value

Standard value: Ø 134 - 134.2 mm

Checking the bell working surface eccentricity

- Install the bell on a driven pulley shaft using 2

bearings (inside diameter: 15 and 17 mm).

- Lock with the original spacer and nut.

- Place the bell/shaft unit on the support to check

the crankshaft alignment.

- Using a feeler dial gauge and the magnetic base,

measure the bell eccentricity.

- Repeat the measurement in 3 positions (Central,

internal, external).

- If faults are found, replace the bell.

Specific tooling

020074Y

Support base for checking crankshaft

alignment

020335Y

Magnetic mounting for dial gauge

Characteristic

clutch housing inspection: Limit eccentricity.

Admissible limit eccentricity: 0.15 mm

Vespa GTS Super 300 ie (2008)

Engine

ENG - 127

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands