background image

Copyright 1999 Patmont Motor Werks. All Rights Reserved.

California

Instruction Manual

for Sport

®

and Liquimatic

®

GO-PED

®

ACCESSORIES LIST

GO-PED

®

PARTS LIST

PART#

DESCRIPTION

PART#

DESCRIPTION

9058

Canvas Carry Bag

1001

Frame

9061

Tool Kit

1002 

Latch Assembly

9062

Go-Mix (Go-Ped Oil Pack)

1006

Wooden Deck

9063

Go-Ped T-Shirt (M,Lg,XLg)

1007

Deck Hardware Kit

1013

Drive Spindle

1014

Drive Spindle Belt

1018

Engine Hardware Kit

1019

Frame / Muffler Connect Tube

1021

Gas Tank Hardware Kit

1022

Handle Lock Tube

1027

Front Fork

1028

Front Fork Bearing Kit

1030

Front Brake Caliper

1031

Front Axle Assembly

1032

Quick Release Axle Assy.

1034

Kick Stand

1039

Wheel Bearings

1043

Handle Hinge FTG Assembly

1046

“T” Handle

1047

Brake Lever Assembly

1049

Grip Set

1050

Throttle Cable Assembly

1051

Throttle Lever

1053

Plastic Cable Tie Set

1054

Brake Cable Assembly

1056

Handle Hinge Pin

1059

Wheel & Tire Assembly

1062

Automatic Safety Spring &
Grip Kit

3114

Enduro Tank

3116

Gas Cap

3120

Fuel Filter Assembly

GO-PED

®

FRAME PARTS

3114

1019

1032

1034

1006

1027

1001

1059

1030

1022

1050

1062

1054

1051

1049

1046

1047

Summary of Contents for Sport







Reviews: