VESPA GTS Super 300 ie 2008 Service Station Manual Download Page 196

Page: 196 / 317

pump circuit6

Check, on switching to "ON", that there is battery

voltage, for about two seconds, to the Black-Green

cable of the pump connector and ground with

pump connector disconnected. Otherwise, check

the continuity of the Black-Green cable between

the pump connector and the remote control base.

Check the efficiency of the ground line of the fuel

pump by measuring the continuity between the

pump connector black cable, system side, and the

ground.

If, when switching to "ON", the pump continues to

turn after two seconds of activation, check, with the

control unit disconnected and the injection load re-

mote control disconnected, that the Black-Purple

cable (pin 20 on the interface wiring) is insulated

from the ground.

Specific tooling

020331Y

Digital multimeter

Circuit leak test

Install the specific tool for checking the fuel pressure, with the pipe fitted with the gauge.

Injection

Vespa GTS Super 300 ie (2008)

INJEC - 196

Summary of Contents for GTS Super 300 ie 2008






























































































































































































































































































































Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands

VESPA GTS Super 300 ie 2008, Service Station Manual

Search results

Summary of Contents for GTS Super 300 ie 2008

Reviews:

Related manuals for GTS Super 300 ie 2008

Brands by name

Popular brands